TOWER UNIT. Assembly Guide x / x / x 600 Tall 50/ x 600 Tall 70/ Door Fridge/Freezer

Transcription

1 2070 x x x 600 Tall 2250 x 600 Tall

2 EORE YOU START INSTAATION SHOUD E PERORMED Y A OMPETENT PERSON ONY. THIS PRODUT OUD E DANEROUS I INORRETY INSTAED OPTION OPTION Panel x2 End Panel Panel x2 ase Panel Panel E x2 Rail Appliance Shelf x1 egs x5 rontal (packed separately) x2 ge racket x2 Sml racket () x4 Hinge Mounting Plate x4 Inc Screws Hinge x4 Inc Screws (U) x2 ixing Plate () x16 Wooden Dowel () x16 am Dowel (Expanding) (H) x12 am lock (K) x10 30mm Screw () x24 15mm Screw (M) x4 over ap (N) x2 Door uffer (Z) x24 Shelf Peg Plastic REQUIRED TOOS NOT to be used with AM DOWE & AM OK Page 1

3 Step 1. Seat dowel () into holes in both end panels () as shown. Step 2. Seat cam dowel () into holes in both end panels () as shown. Seat () cam dowel into hole as shown. E E Step 3. Attach panels () and (E) to panels (), using cam dowel () and also using Dowels () (in orange) in positions as shown. DOWE () & AM DOWE () OATION DETAI N. All AM OK (H) are to be positioned facing the outside of the unit carcass, for ease of tightening. Do not use power tools with cam dowel () or cam lock (H) H H Step 4. Join panels () & (E) to (). Insert cam lock (H). Do NOT tighten until Step 6. View from underside View from underside Page 2

4 ront Step 5. Secure each of the legs into place with 2 x 15mm screws () per leg Ensure legs are rotated as shown so that part of it is supporting the end panels (). ront legs should have flat edge to the front. ront eg position diagram Step 6. ightly hit centre peg of leg base with hammer until flush with the leg base. Step 7 Push leg firmly down into leg base. Adjust legs to 155mm before turning carcass upright. Once in situ level accordingly. Page 3

5 Step 8. Attach hinge plates onto end panels () In locations shown using 8 x 15mm screws () 2070 hinge side to be mounted in accordance to customer kitchen plan. N.. or appliance shelf, secure to panel () using 4 x brackets () locate according to customer appliance requirements. HINE POSITION HINE POSITION 1826mm 1794mm 1826mm 1794mm Example locations ONY Example locations ONY 1086mm 1054mm 846mm 814mm 866mm 834mm 626mm 594mm 126mm 94mm 126mm 94mm rom ase rom ase See ustomer Kitchen Plan for siding. Dimensions relevant for left and right scenario. Page 4

6 2250 Step 8. Attach hinge plates onto end panels () In locations shown using 8 x 15mm screws (). Hinge side to be mounted in accordance to customer kitchen plan. N.. or appliance shelf, secure to panel () using 4 x brackets () locate according to customer appliance requirements. HINE POSITION HINE POSITION 2006mm 1974mm 2006mm 1974mm Example locations ONY Example locations ONY 1026mm 994mm 846mm 814mm 806mm 774mm 626mm 594mm 126mm 94mm rom ase 126mm 94mm rom ase See ustomer Kitchen Plan for siding. Dimensions relevant for left and right scenario. Page 5

7 Securing to Adjacent Units Screw into any side units using the 30mm screws (K) provided to secure to unit. Screw just to the rear of the Hinge Mounting Plate, at the top and bottom of both sides of the unit, place a cover cap on the head to conceal it. K Secure tower to the wall using brackets. Use 2 x 15mm screws () to secure each of the brackets to the cabinets at either side. Then screw through into the wall as shown. Screws for fixing to walls are not provided as these vary depending on your wall material and construction. Ensure appropriate fixings for wall constructions are used. Secure tower to the wall using screws through rail panel (E) into the wall as shown. Screws for fixing to walls are not provided as these vary depending on your wall material and construction. Ensure appropriate fixings for wall constructions are used. E E Page 6

8 See ustomer Specific Kitchen Plan or Tower rontals ixing plates Step 9. Insert hinge where required in holes as shown. ixing plates U U Step 10. Secure hinges by tightening 2 x screws with hinge dowels attached. These are already positioned within the hinges. Step 12. Adjust hinge to suit. As shown below. Step 11. Align doors to join together using 2 x fixing plates (U) to the back of both frontals ensure a 3mm gap is maintained between each frontal once fixed together. Screw in place using 4 x 15mm screws per fixing plate. RONTA HINE ADJUSTMENT To adjust hinge using a screw driver, tighten or loosen as required at points 1 & 2. Point 1 - In - Out Point 2 - side - side Step 13. it cover caps to hinge. Adjust Softclose to suit. Hinge cover caps 1 2 To Release door Pull catch as shown, to release hinge from the hinge plate. View from Inside of arcass The top and bottom hinges MUST be adjusted to the SAME STRENTH. Page 7