Transcription

1 DESCRIPTION CHEMDUR L is a ready to use one-composent product, based on an elastomeric acrylic aqueous dispersion. The dry film has exceptional elasticity to fill microcraks, good protective to proprietes and weatherability minimise water and chloride intrusion. TYPES TYPE M TYPE S TYPE T : Medium : Sand. : Textured or Simulated Stucco. SYSTEMS Medium Finish: Sand Finishes: Textured Finish or Simulated Stucco Type M (2 coats). Type S Base Coat Type M (1 coat). Finish Coat Type S (1 coat). Type T Base Coat Type M (1 coat). Finish Coat Type T (1 coat). ADVANTAGES Excellent adhesion and permanent elasticity. Resists ultraviolet (UV) rays. Lets the substrate breathe. Bridges cracks and micro fissures. Excellent color retention. Available in a variety of decorative colors. Resists mildew and fungus growth. Complies with voc regulations across North America. Can Contribute to LEED points.

2 USES Exterior or interior. Renovation, maintenance or new construction. For use on surfaces not subjected to traffic. A flexible and impermeable coating that breathes: for concrete structures and facades, concrete block, brick and stucco. For residential and commercial buildings, institutions, columns, bridges, overpasses, retaining walls, etc. RECOMMENDATIONS When it is known that there could be accumulations of snow or deicing salts against the coated surface, prior to the application of CHEMDUR L, a coat of a silane water proofing sealer (CHEMDUR S M 20) should be applied. CHEMDUR S M 20 should be applied to the maximum height of known snow and ice accumulation (columns, foundation or retaining walls, bridges etc.) See separate technical data sheet for CHEMDUR S M 20. CHEMDUR L application can proceed the following day. LIMITATIONS Being a water-based product, it must be protected from freezing. Surfaces to be coated must be sound, clean and free of all contamination. Not for recoating of finishes other than CHEMDUR L without prior consultation with CHEMDUR Technical Service. Do not apply on frozen surfaces. Do not apply when there is a risk of rain or freezing or on over-heated surfaces. The minimum ambient and surface temperature for application is 7 C, during application and for at least 18 hours following. Do not use on surfaces that will be subjected to traffic.

3 CHARACTERISTICS Presentation : one-component, colored, water based product Number of coats : 2 minimum Finishes TYPE M : Medium TYPE S : Sand TYPE T : Textured or simulated stucco Colors : Available in colors shown on CHEMDUR COLOR CHART -"Wall Finishes" For custom colors consult Chemdur Customer Service Dept. Viscosity TYPE M : mpa.s. TYPE S : mpa.s. TYPE T : mpa.s. Solids Content (by weight) (by volume) TYPE M : 73% 51% TYPE S : 85% 64% TYPE T : 87% 67% Drying Time To Touch : 1 hour To Recoat : Over night (15 hours) Flammability : non-flammable Clean-up : water for fresh product; xylene for dried product Package Stability : one year in original unopened containers, protected from freezing.

4 CRACK BRIDGING (Determined by the total thickness of dry film of Type I) TYPE I MAXIMUM WIDTH OF CRACK mm mm mm mm mm DRY FILM THICKNESS THAT CAN BE BRIDGED 0.6 mm 0.75 mm 1.0 mm 1.5 mm 2.0 mm PHYSICAL PROPERTIES (Type M) Tensile Strength (ASTM 25 C : 3 0 C : 6 C : 14 mpa Adhesion to concrete : excellent. Elongation (ASTM 25 C : 0 C : C : 150% Flexibility/Type II (2.5cm 23 C) Permeability to water vapour (ASTM 0.5mm dry film Freeze-thaw resistance Resistance to weathering Resistance to mildew and fungus growth : passes. : 5.2 metric perms (8 perms). : very good. : very good. : very good.

5 SURFACE PREPARATION The surface must be sound, solid and free from laitance, grease, oil, rust, paint, sealers, dust or any other material which could detract from the adhesion of CHEMDUR L. Cavities, holes or irregularities should be masticated or filled with a mortar. Hairline cracks that are stable can be masticated or filled with CHEMDUR L Type M applied by brush. APPLICATION Brush, roller, hopper gun (see Table Guide to Application", page 6). Mix well before and occasionally during use. Do not reduce. Allow to dry through before recoating. SYSTEM: MEDIUM Apply two coats of Type M. SYSTEM: SAND Apply the base coat Type M followed by the top coat Type S. SYSTEM: TEXTURED OR SIMULATED STUCCO Apply the base coat Type M followed by the top coat Type T. CLEAN-UP Clean up material with water immediately after use. SECURITY Use with adequate ventilation. Avoid contact with eyes or skin. Wash with soap and water. For more information, consult CHEMDUR Material Safety Data Sheet. KEEP OUT OF REACH OF CHILDREN - FOR INDUSTRIAL USE ONLY

6 GUIDE TO APPLICATION SYSTEM MEDIUM SAND TEXTURED OR SIMULATED STUCCO 1 ST COAT TYPE M METHOD ROLLER 30 mm PILEC COVERAGE m²/l FILM THICKNESS WET DRY mm mm 2 nd COAT TYPE M TYPE S TYPE T METHOD ROLLER 30 mm PILE OR SPRAY ROLLER HOPPER GUN HOPPER GUN COVERAGE m²/l m²/l m²/l m²/l FILM THICKNESS WET DRY mm mm mm mm mm mm mm mm