INSTALLATION INSTRUCTIONS INSTRUCTIONS D INSTALLATION INSTRUCCIONES DE INSTALACIÓN ISTRUZIONI D INSTALLAZIONE

Transcription

1 INSTALLATION INSTRUCTIONS Commercial Gas or Electric Dryer Models MDE18CSAG, MDG18CSAG, MDE18MNAG, MDG18MNAG INSTRUCTIONS D INSTALLATION Sèche-Linge À gaz ou Électrique à usage commercial Modèles MDE18CSAG, MDG18CSAG, MDE18MNAG, MDG18MNAG INSTRUCCIONES DE INSTALACIÓN Secadora a gas o eléctrica comerciale Modelos MDE18CSAG, MDG18CSAG, MDE18MNAG, MDG18MNAG ISTRUZIONI D INSTALLAZIONE Asciugatrice a gas o elettrica commerciale Modelli MDE18CSAG, MDG18CSAG, MDE18MNAG, MDG18MNAG W A

2 TABLE OF CONTENTS. Page Dryer Safety...3 Dryer Disposal...6 Tools & Parts...7 Dimensions/Clearances... 8 Dryer Installation Requirements... 9 Electric Dryer Installation Requirements Gas Dryer Installation Requirements Dryer Venting Requirements Gas Supply Connection Installing Leveling Legs Leveling...17 Complete Installation Reversing Dryer Door Swing Maintenance Instructions If You Need Assistance Technical Specifications Gas Dryer Warranty ÍNDICE. Página Seguridad de la secadora Eliminación de la secadora Herramientas y piezas...47 Dimensiones y espacios libres Requisitos de instalación de secadora Requisitos de instalación de secadora eléctrica Requisitos de instalación de secadora a gas Requisitos de ventilación de la secadora Conexión del suministro de gas Instalación de las patas niveladoras Nivelación Complete la instalación Cómo invertir el sentido de apertura de la puerta Instrucciones de mantenimiento Si necesita ayuda Especificaciones técnicas secadora a gas Garantía TABLE DES MATIÈRES. Page Sécurité du sèche-linge Élimination du sèche-linge Outils et pièces Dimensions/Distances de dégagement Exigences d installation pour le sèche-linge Exigences d installation pour le sèche-linge électrique Exigences d installation pour le sèche-linge à gaz Exigences concernant l évacuation du sèche-linge Raccordement à la canalisation de gaz Installation des pieds de nivellement Nivellement...37 Achever l installation...38 Inversion du sens d ouverture de la porte...39 Instructions d entretien...40 Si vous avez besoin d assistance...40 Fiche technique sèche-linge à gaz...41 Garantie...42 INDICE. Pagina Sicurezza dell asciugatrice Eliminazione dell asciugatrice Attrezzi e componenti...67 Dimensioni/spazi Requisiti dell installazione dell asciugatrice Requisiti dell installazione dell asciugatrice elettrico Requisiti dell installazione dell asciugatrice a gas Requisiti di scarico dell asciugatrice Collegamento di alimentazione del gas Installazione dei piedini di regolazione Livellamento...77 Completamento dell installazione Invertire il senso di apertura dello sportello Istruzioni di manutenzione Se avete bisogno dell assistenza Dati tecnici asciugatrice a gas Garanzia

3 DRYER SAFETY It is recommended that the owner post, in a prominent location, instructions for the customer s use in the event the customer smells gas. This information should be obtained from your gas supplier. Post the following warning in a prominent location. FOR YOUR SAFETY 1. DO NOT USE OR STORE PETROL OR OTHER FLAMMABLE MATERIALS IN THIS APPLIANCE OR NEAR THIS APPLIANCE. 2. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION. 3. DO NOT MODIFY THIS APPLIANCE. 3

4 DRYER SAFETY IMPORTANT: When discarding or storing your old clothes dryer, remove the door. 4

5 DRYER SAFETY IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions, including the following: Read all instructions before using the dryer. This dryer is intended only for drying clothes and textiles that have been washed in water. Do not use for any other purpose. WARNING: If you smell gas, do not use the dryer or any electrical equipment nearby. Warn other people to clear the area. Contact the dryer owner immediately. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire. If it is unavoidable that fabrics that contain vegetable or cooking oil or that have been contaminated by hair care products be placed in a tumble dryer, they should first be washed in hot water with extra detergent this will reduce, but not eliminate the hazard. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with petrol, dry-cleaning solvents, other flammable, or explosive substances as they give off vapors that could ignite or explode. Items that have been soiled with substances such as acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes, and wax removers should be washed in hot water with extra detergent before being dried in the dryer. Do not dry unwashed items in the dryer. Do not use this dryer if industrial chemicals have been used for cleaning. The possible presence of residual quantities of aggressive or decomposed chemicals in the load may produce damage to the dryer and harmful fumes. Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children. This dryer is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the dryer by a person responsible for their safety. Before the dryer is removed from service or discarded, remove the door to the dryer compartment. Do not reach into the dryer if the drum is moving. Do not open door while dryer is in operation. It will stop. When loading or re-loading the dryer, avoid touching hot metal parts of the drum (burn risk). If drum rotation is blocked due to trapped textiles, disconnect the dryer from the electrical supply before gently removing the blockage. If the dryer is not heating, or appears to be defective or damaged, do not use it. Contact the owner. Do not install or store the dryer where it will be exposed to the weather. Do not tamper with controls. Clean dryer lint screen before or after each load. Do not use this dryer without the lint screen in place. Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Installation Instructions or in published user-repair instructions that you understand and have the skills to carry out. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials. The final part of a tumble dryer cycle occurs without heat (cool-down cycle) to ensure that the articles are left at a temperature that ensures that the items will not be damaged. WARNING: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. (Avoids risk of spontaneous combustion). In case of electrical supply failure, remove the load quickly and spread it out to avoid risk of spontaneous combustion. Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt. The fresh air ventilation openings into the room and into the dryer must not be blocked or sealed. Emergency stop control: The mains plug should be removed in an emergency. The interior of the dryer and dryer exhaust vent should be cleaned periodically by qualified service personnel. See Electrical Requirements section for earthing instructions. SAVE THESE INSTRUCTIONS 5

6 DRYER DISPOSAL MODEL NOMENCLATURE: MDG Maytag Gas MDE Maytag Electric 18 Model Type Number CS Coin Operated MN Non-Pay 6

7 TOOLS & PARTS Tools Needed: 203 mm (8") 203 mm (8") or 254 mm (10") Flat-Blade Screwdriver Phillips Screwdriver or 254 mm (10") Adjustable Wrench Pipe Wrench that opens to 25 mm ( 1") Torx T-20 Security 25 mm (1") Hex-Head 8 mm ( 5 16") Socket Wrench Pliers (that open to Screwdriver or Bit Socket Wrench 39 mm [1 9 /16"]) Level Utility Knife 6 mm (1/4") Nut Driver 686 mm (27") Wood Block Caulk Gun and Caulk Vent Clamps Pipe-Joint Compound Putty Knife (for installing new exhaust vent) Suitable for Gas Type Flashlight (optional) 25 mm (1") Ruler or Measuring Tape Open-End Wrenches Parts Supplied: Foot Boots (4) Leveling Legs (4) NOTE: The circuit diagram for this dryer is located inside the lower front panel, within the Tech Sheets. Technical Specifications: V, 50 Hz. AC 4575W Total mass: 68 kg max. Clothes Capacity: 9 kg max. NOTE: Sound Pressure Level, Lpa: 58 dba (uncertainty, Kpa: +/ 10 dba). TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC. 7

8 DIMENSIONS/CLEARANCES Dimensions Side View 743 mm (29 1 /4") 648 mm (25 1 /2") Back View 686 mm (27") Electric 889 mm (35") 210 mm (8 1 /4") 83 mm (3 1 /4") 38 mm (1 1 /2") 140 mm (5 1 /2") 343 mm (13 1 /2") Gas 279 mm (11") 102 mm (4" dia) 889 mm (35") (electric models) 1048 mm (41 1 /4") 940 mm (37") (gas models) 330 mm (13") 83 mm (3 1 /4") 25 mm (1") 260 mm (10 1 /4") Bottom Exhaust 178 mm (7") 359 mm (14 1 /8") Clearances Recessed Front View Closet Side View 381 mm (15") 356 mm (14") 0 mm (0") 0 mm (0") 25 mm (1") 0 mm (0") 8

9 Location Requirements DRYER INSTALLATION REQUIREMENTS (Australia and New Zealand for full details of installation requirements refer to AS/NZS ) Your dryer can be installed in a basement, laundry room, or recessed area. This dryer is not intended for installation in a mobile home. Companion appliance location requirements should also be considered. IMPORTANT: Do not install or store the dryer where it will be exposed to the weather. Proper installation is your responsibility. Recessed Area and Closet Installation Instructions This dryer may be installed in a recessed area or closet. For recessed area and closet installations, minimum clearances can be found on the warning label on the rear of the dryer or in Dimensions/Clearances. The installation spacing is in millimeters and is the minimum allowable. Additional spacing should be considered for ease of installation, servicing, and compliance with local codes and ordinances. If closet door is installed, the minimum unobstructed air opening in the top and bottom is required. Louvered doors with equivalent air openings are acceptable. The dryer must be exhausted outdoors. No other fuel-burning appliance may be installed in the same closet as the dryer. NOTE: For installation in Australia and New Zealand, refer to AS/NZS for ventilation requirements. You will need: An earthed electrical outlet located within 1.8 m (6 ft.) of where the power cord is attached to the back of the dryer. See Electrical Requirements. A level floor with a maximum slope of 25 mm (1") under entire dryer. Installing the dryer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended. Dryer installation clearances The location must be large enough to allow the dryer door to be fully opened. Additional spacing should be considered for ease of installation and servicing. The door opens more than 180. Additional clearances might be required for wall, door, and floor moldings. Additional spacing of 25 mm (1") on all sides of the dryer is recommended to reduce noise transfer. When installing a dryer: IMPORTANT: Observe all governing codes and ordinances. Check code requirements: Some codes limit or do not permit installation of clothes dryers in garages, closets, or sleeping quarters. Contact your local building inspector. NOTE: For installation in Australia and New Zealand, install dryer in accordance with AS/NZS and local governance codes. Gas Dryers only: Make sure that lower edges of the cabinet, plus the back and bottom sides of the dryer, are free of obstructions to permit adequate clearance of air openings for combustion air. See Recessed Area and Closet Installation Instructions below for minimum spacing requirements. Front View Closet Door 9

10 ELECTRIC DRYER INSTALLATION REQUIREMENTS Electrical Requirements IMPORTANT: Observe all governing codes and ordinances. This dryer is supplied without an electric cord and plug. It must be connected by a competent electrician to a single-phase electricity supply at the voltage shown on the dataplate, using a suitable fixed wiring installation in accordance with local and national wiring regulations. n A 3-wire circular cord of minimum conductor size 2.5 mm 2 cross-section area should be used. n A 25A (minimum) supply fuse should be used, and a switch having a contact separation in both poles that provides full disconnection under over-voltage category III conditions must be incorporated into the fixed wiring in accordance with local wiring regulations. The dryer should be positioned so that the disconnection switch is clearly visible and easily accessible to the user. This disconnection switch also provides the function of an emergency stop control for the user. n A cord clamp bush is provided on the dryer, and should be tightened on completion of wiring. The electrical mains terminals are located behind the small rear access panel (terminal block cover), and connections should be made in accordance with the terminal markings. Remember to replace the terminal access panel (terminal block cover). NOTE: In accordance with the European EMC Directive (2004/108/EC), the maximum electrical supply system impedance to which the electric dryer should be connected is declared to be Ohm + j0.034 Ohm. NOTE: Electrical safety standards: The manufacturer has chosen compliance with IEC/EN standards as the most appropriate for this product. This is 3-wire appliance which must be earthed. If codes permit and an additional earth bond wire is used, it is recommended that a qualified electrician determine that the earth bond path is adequate. Recommended Earthing Method It is your responsibility to contact a qualified electrical installer to ensure that the electrical installation is adequate and in conformance with all local codes and ordinances. 10

11 GAS DRYER INSTALLATION REQUIREMENTS Electrical Requirements EARTHING INSTRUCTIONS IMPORTANT: Observe all governing codes and ordinances. You will need an earthed electrical outlet located within 610 mm (2 feet) of either side of the dryer. This dryer is supplied/fitted with an electrical supply cord and plug. It should be connected to electrical supply socket at the voltage shown on the rating plate. The minimum supply fuse capacity should be 10A. The dryer must be positioned so that the plug is clearly visible and accessible. This plug also provides the function of an emergency stop control for the user. If the fitted plug is not used, the electrical connection must be carried out by a competent electrician in accordance with local or national codes. If the supply cord is damaged, it must be replaced with a specially terminated cord by an authorized service agent or a similarly competent person in order to avoid a hazard. Do not use an adapter. Do not use an extension cord. NOTE: In accordance with the European EMC Directive (2004/108/EC), the maximum electricity supply system impedance to which the gas dryer should be connected is declared to be Ohm + j0.034 Ohm. NOTE: Electrical safety standards: The manufacturer has chosen compliance with IEC/EN standards as the most appropriate for this product. SAVE THESE INSTRUCTIONS Using the universal cord included with this dryer: The gas dryer is equipped with a universal cord with interchangeable plugs. 1. To use the universal cord, select the plug end that fits your electrical outlet, and plug it into the adapter on the supply cord. 2. Secure the plug end in place on the cord by aligning the 2 cover halves over the cord adapter and clipping them together. If codes permit and an additional earth bond wire is used, it is recommended that a qualified electrician determine that the earth bond path is adequate. 11

12 GAS DRYER INSTALLATION REQUIREMENTS Gas Supply IMPORTANT: Observe all governing codes and ordinances. In Australia and New Zealand, refer to AS/NZS Gas Installations. Gas Supply Before installation, check that the local gas distribution conditions, nature of gas and pressure, and the adjustment of the appliance are compatible. Burner information will be found on the model/ serial rating plate in the door recess of the dryer. If this information does not agree with the type of gas available, see your dealer. Natural Gas: This dryer is factory adjusted for use with NATURAL GAS (G20), and no further adjustment should be required at installation. L.P. Gas: This dryer is also certified for use with L.P. (propane or butane) gases with appropriate conversion. No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. Conversion must be done by a competent service technician. Gas conversion kit (European Country), part number W , is available for purchase from your dealer. Gas conversion kit (Australia), part number W , is available for purchase from your dealer. Full instructions are supplied with the kit. Natural Gas (France/Belgium): This dryer is also certified for France/Belgium for use with G20/ G25 gases (20 mbar/25 mbar) with appropriate conversion. No attempt should be made to convert this appliance from the gas specified on the gas rating label for use with a different gas without consulting the serving gas supplier. Gas conversion must be done by a qualified gas service technician. Conversion kit, part number (W ) is available for purchase from your dealer. Full instructions are supplied with the kit. Supply line requirements: Provide a rigid gas supply line to the dryer location. It should be minimum 12.5 mm (1/2") ID. When acceptable to the gas supplier and local codes, 10 mm (3/8") ID rigid supply line may be used for lengths under 6.1 m (20'). Pipe-joint compounds resistant to the action of L.P. gas must be used. NOTE: For installation in Australia and New Zealand, refer to AS/NZS 5601 for pipe sizing details. All piping is to be in accordance with AS/NZS Gas Installations. Gas connection to the dryer itself should be made by means of a flexible gas hose suitable for the appliance and gas category in accordance with national installation regulations. If in doubt, contact the gas supplier. It should be minimum 10 mm (3/8") ID. A means of restraint should be used between the dryer and the wall to avoid straining of the rigid gas supply when the dryer is moved. An appropriate length of chain and a wall hook is recommended. The dryer gas inlet connection is a 3/8" NPT thread. An adapter is supplied for conversion to standard ISO thread (3/8" BSP). Check for leaks by using an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found. A pressure measurement tapping is provided on the gas valve within the dryer, accessible after removal of the lower front panel. The dryer must be disconnected from the gas supply piping system during any pressure testing of that system. 12

13 DRYER VENTING REQUIREMENTS Elbows: 45 elbows provide better airflow than 90 elbows. Good Better WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. In Australia and New Zealand, refer to AS/NZS Gas Installations. Clamps: Use clamps to seal all joints. Exhaust vent must not be connected or secured with screws or other fastening devices that extend into interior of duct and catch lint. Do not use duct tape. Dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Only rigid or flexible metal vent shall be used for exhausting. 102 mm (4") 102 mm (4") Heavy, Metal Exhaust Vent Improper venting can cause moisture and lint to collect indoors, which may result in: Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc. Housecleaning problems and health problems. Only a 102 mm (4") heavy, metal exhaust vent and clamps may be used. Do not use plastic or metal foil vent. Rigid metal vent: Recommended for best drying performance and to avoid crushing and kinking. Flexible metal vent: (Acceptable only if accessible to clean) Must be fully extended and supported in final dryer location. Remove excess to avoid sagging and kinking that may result in reduced airflow and poor performance. Do not install in enclosed walls, ceilings, or floors. The total length should not exceed 2.4 m (7 3 4 ft.). NOTE: If using an existing vent system, clean lint from entire length of the system and make sure exhaust hood is not plugged with lint. Replace plastic or metal foil vents with rigid metal or flexible metal vents. Review Vent System Chart and if necessary, modify existing vent system to achieve best drying performance. 13

14 DRYER VENTING REQUIREMENTS Vent Hoods 102 mm (4") Diameter Exhaust Hoods Exhaust hood must be at least 305 mm (12") from the ground or any object that may be in the path of the exhaust (such as flowers, rocks, bushes, or snow). Box Hood Louvered Hood Angled Hood " min. mm min. (305 (12") mm) Vent System Length Maximum Vent Length/Vent Connection Maximum length of vent system depends upon the type of vent used, number of elbows, and type of exhaust hood. Vent System Chart (Rigid Metal Vent) No. of Box and Angled 90 Turns Louvered Hood Hood m (130 ft.) 39.3 m (129 ft.) m (125 ft.) 36.3 m (119 ft.) m (115 ft) 33.2 m (109 ft.) m (106 ft.) 30.5 m (100 ft.) m (98 ft.) 28.0 m (92 ft.) For vent systems not covered by the vent specification chart, see your parts distributor. Provision must be made for enough air for combustion and ventilation. (Check governing codes and ordinances.) See Recessed Area and Closet Installation Instructions in the Location Requirements section. A 102 mm (4") outlet hood is preferred. However, a 64 mm (2 1 2") outlet exhaust hood may be used. A 64 mm (2 1 2") outlet creates greater back pressure than other hood types. For permanent installation, a stationary vent system is required. Connect Vent 1. If connecting to existing vent, make sure the vent is clean. 2. Using a 102 mm (4") clamp, connect vent to exhaust outlet in dryer. Vent Collar 3. Tighten hose clamp with Phillips screwdriver. 4. Make sure the vent is secured to exhaust hood with a 102 mm (4") clamp. 5. Move dryer into final position. Do not crush or kink vent. Make sure dryer is level. NOTE: Do not remove vent collar. 14

15 DRYER VENTING REQUIREMENTS If an Exhaust Hood Cannot be Used The outside end of main vent should have a sweep elbow directed downward. * Minimum clearance above any accumulation of snow, ice, or debris such as leaves If main vent travels vertically through the roof, rather than through wall, install a 180 sweep elbow on end of vent at least 610 mm (2 ft.) above surface of roof. The opening in wall or roof shall have a diameter 13 mm (1 2") larger than vent diameter. Vent should be centered in opening. Do not install screening over end of vent for best performance. Multiple Dryer Venting A main vent can be used for venting a group of dryers. The main vent should be sized to remove 5663 l/min. (200 CFM) of air per dryer. Large-capacity lint screens of proper design may be used in main vent if checked and cleaned frequently. The room where the dryers are located should have make-up air equal to or greater than CFM of all the dryers in the room. Back-draft dampers are available from your distributor and should be installed in the vent of each dryer to keep exhausted air from returning into dryers and to keep exhaust in balance within main vent. Unobstructed return air openings are required. Although usually each single-load dryer should have an unobstructed outdoor air opening of 154 cm 2 (24 in. 2 ) (based on 6.5 cm 2 [1 in. 2 ] per 252 kcal [1,000 Btu]), common make-up air openings are also acceptable. Set up common openings so the make-up air is distributed equally to all of the dryers. Keep in mind that the coverage area must be increased by 33% to account for the use of registers or louvers over the openings. Also, make-up air openings should not be installed near the location where exhaust vents exit the building. Each vent should enter the main vent at an angle pointing in the direction of the airflow. Vents entering from the opposite side should be staggered to reduce the exhausted air from interfering with the other vents. 30 max. air Air flow Flow The maximum angle of each vent entering the main vent should be no more than 30. Keep air openings free of dry cleaning fluid fumes. Fumes create acids which, when drawn through the dryer heating units, can damage dryers and items being dried. A clean-out cover should be located on the main vent for periodic cleaning of the vent system. GAS SUPPLY CONNECTION (on some models) Make Gas Connection 3. Open the shut-off valve in the gas supply line and make sure the dryer has its own gas supply opened. 4. Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leaks found. 1. Remove red cap from gas pipe on back of dryer. 2. Connect gas supply to dryer. If the flexible gas hose has 10 mm (3/8") BSP thread, use the supplied conversion thread adapter. Use pipe-joint compound resistant to the action of L.P. gas for gas connections. If necessary for service, open the toe panel. Use a putty knife to press on the 2 toe panel locks located at the top of the toe panel. Pull downward on the toe panel to open. Toe panel is hinged at the bottom. 15

16 INSTALLING LEVELING LEGS 1. Prepare dryer for leveling legs NOTE: Slide dryer onto cardboard or hardboard before moving to avoid damaging floor covering. Using two or more people, move dryer to desired installation location. Take tape off front corners of dryer. Open dryer and remove the literature and parts packages. Wipe drum interior with a damp cloth to remove any dust. Take two cardboard corners from the dryer carton and place them on the floor in back of the dryer. Firmly grasp the body of the dryer and gently lay it on its back on the cardboard corners. 2. Screw in leveling legs Examine leveling legs and find diamond marking. Screw legs into leg holes by hand. Use an adjustable wrench or 25 mm (1") hex-head socket wrench to finish turning legs until diamond marking is no longer visible. Then fit a covered foot boot over each leg foot. Diamond Marking Foot To protect the floor, use a large piece of cardboard from the dryer carton. Stand dryer up on the cardboard. Slide the dryer until it is close to its final location. Leave enough room for electrical connection and to connect the exhaust vent. 16

17 LEVELING Leveling your dryer properly reduces excess noise and vibration. 2. Grip dryer from top and rock back and forth, making sure all four legs are firmly on floor. Repeat, rocking dryer from side to side. If dryer rocks, go to Step 3 and adjust leveling legs. 1. Remove cardboard from beneath dryer. Place a level on top edges of dryer, checking each side and front. If not level, tip dryer and adjust legs up or down as shown in Step 3, repeating as necessary. 3. If dryer is not level, use a 25 mm or 1" open-end or adjustable wrench to turn the leveling leg counterclockwise to lower the dryer or clockwise to raise the dryer. Recheck levelness of dryer and that all four legs are firmly in contact with the floor. Repeat as needed. HELPFUL TIP: You may want to prop up front of dryer about 102 mm (4") with a wood block or similar object that will support weight of dryer. Not Level LEVEL Not Level 17

18 COMPLETE INSTALLATION 1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended earthing method. See Electrical Requirements. 2. Check that all parts are now installed. If there is an extra part, go back through the steps. 3. Check that you have all of your tools. 4. Dispose of/recycle all packaging materials. WARNING Electric Shock Hazard This dryer must be earthed. Securely tighten all electrical connections. Failure to do so can result in death, fire, or electric shock. 6. Check dryer operation (some accumulated time may be on the timer due to factory testing). Close dryer door. Insert coins in slide and press slide in slowly. (Operating time will accumulate per number of coins and type of timing cam used.) Push START button. Using a full heat cycle (not the air cycle), let the dryer run for at least five minutes. Dryer will stop when time is used up. NOTE: Dryer door must be closed for dryer to operate. When door is open, dryer stops, but timer continues to run. To restart dryer, close door and push START button. 7. Gas Models only: Open the dryer door. Check that the inside of the dryer is warm. If the burner does not ignite and you can feel no heat inside the dryer, shut off dryer for five minutes. Check that all supply valve controls are in ON position and that the electrical cord is plugged in. Repeat five-minute test. 8. If drying time is too long, make sure that the lint screen is clean and that there are no obstructions to airflow in the dryer vent system. 9. Restart the dryer and allow it to complete a full heat cycle (not air cycle) to make sure it is working properly. 5. Plug into an earthed outlet, or connect power. 18

19 REVERSING DRYER DOOR SWING (OPTIONAL) You can change your door swing from a right-side opening to left-side opening, if desired. Remove the Door Assembly 1. Place a towel or soft cloth on top of dryer or work space to avoid scratching of the surface. 2. Open dryer door. Remove bottom screws from cabinet side of hinges. Loosen (do not remove) top screws from cabinet side of hinges. 7. Be certain to keep cardboard spacer centered between doors. Reattach outer door panel to inner door panel so handle is on the side where hinges were just removed. Towel 8. Reattach screws at top, bottom, and side of door (5 screws). Hinges 3. Lift door until top screws in cabinet are in large part of hinge slot. Pull forward off screws. Set door (handle side up) on top of dryer. Remove top screws from cabinet. 4. Remove screws attaching hinges to door. 5. Remove screws at top, bottom, and side of door (5 screws). 9. Attach door hinges to dryer door so that larger hole is at the bottom of the hinge and the hinge pin is toward the door front. 6. Holding door over towel on dryer, grasp sides of outer door and gently lift to separate it from inner door. Do not use a putty knife to pry apart. Do not pull on door seal or plastic door catch. 10. Remove the 4 screws that attach 2 plugs on the left side. Attach plugs to right side using the same 4 screws. 11. Insert screws into bottom holes on left side of cabinet. Tighten screws halfway. Position door so large end of door hinge slot is over screws. Slide door up so screws are in bottom of slots. Tighten screws. Insert and tighten top screws in hinges. 12. Close door and check that door strike aligns with door catch. If needed, slide door catch left or right within slot to adjust alignment. 19

20 MAINTENANCE INSTRUCTIONS Clean lint screen before and after each cycle. Removing accumulated lint: From inside the dryer cabinet: Lint should be removed every 2 years or more often, depending on dryer usage. Cleaning should be done by a qualified person. From the exhaust vent: Lint should be removed every 2 years, or more often, depending on dryer usage. Keep area around dryer clear and free from combustible materials, petrol, and other flammable vapors and liquids. Keep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air. If dryer does not operate, check the following: Electrical supply is connected. Circuit breaker is not tripped or house fuse is not blown. Door is closed. Listen closely to hear the door switch activate. Controls are set in a running or on position. START button has been pushed firmly. For gas dryers, check that gas supply shut-off valves are set in open position. IF YOU NEED ASSISTANCE If you need help, contact the dealer from whom you purchased the appliance, or a Maytag designated service company. When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request. EU - DECLARATION OF CONFORMITY CE - DECLARATION DE CONFORMITE WE (nous): BAUKNECHT HAUSGERÄTE GmbH, D Schorndorf representing (représentant): WHIRLPOOL EUROPE S.r.l I COMERIO declare under our sole responsibility that the product déclarons sous notre propre responsabilité que le produit dryer Maytag MDE18CS (séche linge): Maytag MDE18MN Whirlpool XCEM2763 to which this declaration relates is in conformity with the following standard(s) or other normative document(s) auquel se référe cette déclaration est conforme aux normes suivantes ou autres documents normatifs EN : 2002+A1+A2+A11+A12+A13+A14+A15 EN : 2010 EN 62233: 2008+Ber.1: 2008 EN ISO : 2008 EN ISO : 2008 EN : 2006+A1:2009+A2:2011 (Test method > 30 MHz: Disturbance power) EN : 1997+A1:2001+A2:2008 EN : 2005 EN : 2000 following the provisions of Directive(s): suivant les previsions des Directives: EU - DECLARATION OF CONFORMITY CE - DECLARATION DE CONFORMITE WE (nous): BAUKNECHT HAUSGERÄTE GmbH, D Schorndorf representing (représentant): WHIRLPOOL EUROPE S.r.l I COMERIO declare under our sole responsibility that the product déclarons sous notre propre responsabilité que le produit dryer Maytag MDG18CS (séche linge): Maytag MDG18MN Whirlpool XCGM2763 to which this declaration relates is in conformity with the following standard(s) or other normative document(s) auquel se référe cette déclaration est conforme aux normes suivantes ou autres documents normatifs EN : 2012 EN : 2006+A1:2010 incl. Corr 1&2 EN 62233: 2008+Ber.1: 2008 EN ISO : 2008 EN ISO : 2008 EN : 2006+A1:2009+A2:2011 (Test method > 30 MHz: Disturbance power) EN : 1997+A1:2001+A2:2008 EN :2006+A1:2009+A2:2009 EN :2008 following the provisions of Directive(s): suivant les previsions des Directives: 2006/42/EC Machinery Directive (CEE Directive Machine) 2006/95/EC Low Voltage Directive (CEE Directive Basse Tension) 2004/108/EC Electromagnetic Compatibility Directive (CEE Directive Compatibilité Electro-magnétique) 2011/65/EU RoHS Directive (CEE Directive RoHs) Schorndorf, Micael Zirondi Karl-Dieter Klingenstein Place and date: Director PDC FC EMEA Product Approval lieu et date GPO, Schorndorf 2006/42/EC Machinery Directive (CEE Directive Machine) 2006/95/EC Low Voltage Directive (CEE Directive Basse Tension) 2009/142/EC Gas Appliances Directive (CEE Directive relative aux appareils à gaz) 2004/108/EC Electromagnetic Compatibility Directive (CEE Directive Compatibilité Electro-magnétique) 2011/65/EU RoHS Directive (CEE Directive RoHs) Schorndorf, Micael Zirondi Karl-Dieter Klingenstein Place and date: Director PDC FC EMEA Product Approval lieu et date GPO, Schorndorf Name and signature of aurthorised person Nom et signature de la personne autorisée Year of CE Marking (Année d apposition du marquage CE): 2013 Name and signature of aurthorised person Nom et signature de la personne autorisée Year of CE Marking (Année d apposition du marquage CE):

21 TECHNICAL SPECIFICATIONS GAS DRYER V~50Hz 1ph 3A max. IP24 Clothes capacity: 9.0 kg max. Sound pressure level, Lpa: 58 dba (uncertainty, Kpa: +/-10 dba) Total mass: 68 kg max. Factory set for NATURAL GAS: Injector size: 2.2 mm Heat input gross: 5.9 kw Country: CH, CZ, CY, ES, GB, GR, HR, IE, IT, PT, SI, SK, TR CY, CZ, DK, EE, FI, GR, HU, IT, NO, RO, SE, SK, TR European Gas Category: II 2H3+ II 2H3B/P Gas Flow Rate: m 3 /hr m 3 /hr Supply Pressure (G20): 20 mbar 20 mbar Factory Adjusted Pressure: 7.4 mbar 7.4 mbar With LP Gas Conversion Kit: Injector size: 1.25 mm Heat input gross: 6.4 kw European Country: CH, CZ, CY, ES, GB, GR, HR, IE, IT, PT, SI, SK, TR CY, CZ, DK, EE, FI, GR, HU, IT, NO, RO, SE, SK, TR European Gas Category: II 2H3+ II 2H3B/P Butane Supply Pressure (G30): mbar 30 mbar Adjusted Pressure: N/A N/A Propane Supply Pressure (G31): 37 mbar 30 mbar Adjusted Pressure: N/A N/A With France/Belgium NATURAL GAS conversion kit: Injector size 1.65 mm Heat input gross: 5.9 kw European Country: FR, BE European Gas Category: I 2E+ Supply Pressure (G20): Supply Pressure (G25): Adjusted Pressure: Country: Supply Pressure (G20) Adjusted Pressure (Test Point Pressure): Nominal Hourly Gas Consumption Country: Propane Supply Pressure: Adjusted Pressure: Nominal Hourly Gas Consumption: 20 mbar 25 mbar Factory set for Australia/New Zealand NATURAL GAS: Injector size: 2.2 mm Heat input gross: 5.9 kw N/A AS, NZS minimum 1.13 kpa 0.74 kpa 21.1 MJ/h With Australia LG Gas Conversion Kit: Injector Size: 1.40 mm Heat input gross: 6.54 kw Factory set for NATURAL GAS: Injector size: 2.2 mm Heat input gross: 5.0 kw AS, NZS 2.75 kpa 2.75 kpa 23 MJ/h Country: European Gas Category: Gas Flow Rate: Supply Pressure (G25): Factory Adjusted Pressure (G25) : Supply Pressure (G30/G31): Factory Adjusted Pressure (G30/G31): NL II 2L3B/P m 3 /hr 25 mbar 7.4 mbar 30 mbar N/A NOTE: Conversion kit: From Natural Gas to LP Gas - Europe: Whirlpool Part No. W Conversion kit: From Natural Gas to LP Gas - Australia: Whirlpool Part No. W Conversion kit: From Natural Gas to Natural Gas - France/Belgium: Whirlpool Part No. W Manufacturer: Whirlpool Corporation, Benton Harbor, Michigan 49022, U.S.A. Manufacturing Site: Whirlpool Corporation, 1300 Marion-Agosta Rd., Marion, OH, 43302, U.S.A. EU Representatives: Maytag UK Ltd., 2 St. Annes Blvd., Redhill, RH1 1AX, UK & Bauknecht Hausgeräte GmbH, D Schorndorf, Germany 21

22 MAYTAG COMMERCIAL WASHER, DRYER, STACKED DRYER/ DRYER, COMMERCIAL STACK LAUNDRY, AND MULTI-LOAD COIN OPERATED COMMERCIAL WASHERS AND DRYERS WARRANTY LIMITED WARRANTY ON PARTS For the first five years from the date of purchase, when this commercial appliance is installed, maintained and operated according to instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation (thereafter Maytag ) will pay for factory specified parts or original equipment manufacturer parts to correct defects in materials or workmanship. Proof of original purchase date is required to obtain service under this warranty. ITEMS MAYTAG WILL NOT PAY FOR 1. All other costs including labor, transportation, or custom duties. 2. Service calls to correct the installation of your commercial appliance, to instruct you how to use your commercial appliance, to replace or repair fuses, or to correct external wiring or plumbing. 3. Repairs when your commercial appliance is used for other than normal, commercial use. 4. Damage resulting from improper handling of product during delivery, theft, accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with local electrical or plumbing codes, or use of products not approved by Maytag. 5. Pickup and Delivery. This commercial appliance is designed to be repaired on location. 6. Repairs to parts or systems resulting from unauthorized modifications made to the commercial appliance. 7. The removal and reinstallation of your commercial appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions. 8. Chemical damage is excluded from all warranty coverage. 9. Changes to the building, room, or location needed in order to make the commercial appliance operate correctly. 10. Repairs made by a non-whirlpool authorized service technician. DISCLAIMER OF IMPLIED WARRANTIES; LIMITATIONS OF REMEDIES CUSTOMER S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE. If you need service, please contact your authorized Maytag Commercial Laundry distributor. To locate your authorized Maytag Commercial Laundry distributor, or for web inquiries, visit For written correspondence: Maytag Commercial Laundry Service Department 2000 M-63 North Benton Harbor, Michigan USA 1/11 22

23 SECURITE DU SECHE-LINGE On recommande que le propriétaire place les instructions à l usage du client en un lieu bien visible, au cas où le client percevrait une odeur de gaz. Ces renseignements doivent être obtenus auprès de votre fournisseur en gaz. Placer l avertissement qui suit à un endroit bien visible. POUR VOTRE SECURITE 1. NE PAS UTILISER OU REMISER D ESSENCE OU AUTRES MATÉRIAUX INFLAMMABLES DANS CET APPAREIL MÉNAGER O U À PROXIMITÉ DE CELUI-CI. 2. NE PAS VAPORISER D AÉROSOLS À PROXIMITÉ DE CET APPAREIL MÉNAGER LORSQU IL EST EN FONCTIONNEMENT. 3. NE PAS MODIFIER CET APPAREIL MÉNAGER. 23

24 SECURITE DU SECHE-LINGE IMPORTANT : Pour mettre l ancien sèche-linge au rebut ou pour la remiser, enlever la porte. 24

25 SECURITE DU SECHE-LINGE IMPORTANTES INSTRUCTIONS DE SÉCURITÉ AVERTISSEMENT : Pour réduire les risques d incendie, de choc électrique ou de blessures lors de l utilisation du sèche-linge, suivre les précautions fondamentales dont les suivantes : Lire toutes les instructions avant d utiliser le sèche-linge. Ce sèche-linge est conçue uniquement pour le séchage de vêtements et de textiles ayant été nettoyés à l eau. Ne pas l utiliser à toute autre fin. AVERTISSEMENT: Si l on détecte une odeur de gaz, ne pas utiliser le sèche-linge ou tout autre équipement électrique situé à proximité. Avertir les autres personnes qu elles doivent évacuer cette zone. Contacter le propriétaire du sèche-linge immédiatement. Ne pas placer des articles exposés aux huiles de cuisson dans votre sèche-linge. Les articles contaminés par des huiles de cuisson peuvent contribuer à une réaction chimique qui pourrait causer à la charge de s enflammer. Si on doit absolument placer des tissus qui contiennent de l huile végétale ou de cuisson ou qui ont été contaminés par des produits de soin des cheveux dans un sèche-linge, faut d abord les laver dans de l eau chaude avec un supplément de détergent; ceci réduira le danger, sans toutefois l éliminer. Ne pas faire sécher des articles qui ont été nettoyés ou lavés avec de l essence ou imbibés d essence, solvants de nettoyage à sec, ou autres substances inflammables ou explosives; ces substances peuvent émettre des vapeurs susceptibles de s enflammer ou d exploser. Les articles qui ont été souillés avec des substances comme de l acétone, de l alcool, du pétrole, du kérosène, des détachants, de la térébenthine, des cires et des décapants pour cire doivent être lavés à l eau chaude avec un supplément de détergent avant d être séchés dans le sèche-linge. Ne pas faire sécher dans le sèche-linge des articles nonlavés. Ne pas utiliser ce sèche-linge si l on a utilisé des produits chimiques industriels pour le nettoyage. La présence éventuelle de quantités résiduelles de produits chimiques corrosifs ou décomposés dans la charge peut endommager le sèche-linge et produire des fumées toxiques. Ne pas laisser des enfants jouer sur ou à l intérieur du sèche-linge. Bien surveiller les enfants lorsque le sèche-linge est utilisé à proximité d enfants. Ce sèche-linge n est pas conçu pour une utilisation par des personnes (notamment des enfants) aux capacités physiques, sensorielles ou mentales réduites, ou manquant d expérience ou de connaissances, à moins qu elles soient supervisées par une personne responsable ou aient reçu des instructions adaptées pour utiliser le sèche-linge en toute sécurité. Avant de retirer le sèche-linge pour un dépannage ou pour le jeter, ôter la porte du compartiment du sèche-linge. Ne pas tenter d atteindre un article à l intérieur de la cuve du sèche-linge lorsque le tambour est en mouvement. Ne pas ouvrir la porte lorsque le sèche-linge est en marche. Il s arrêtera. Lors du chargement ou du rechargement du sèche-linge, éviter de toucher les parties métalliques chaudes du tambour (risque de brûlure). CONSERVEZ CES INSTRUCTIONS Si la rotation du tambour est entravée par des tissus coincés, déconnecter le sèche-linge de l alimentation électrique avant de retirer la source d obstruction avec précaution. Ne pas utiliser le sèche-linge s il ne chauffe pas, s il semble défectueux ou endommagé. Contacter le propriétaire. Ne pas installer ou remiser ce sèche-linge à un endroit où il serait exposée aux intempéries. Ne pas modifier les organes de commande. Nettoyer le filtre à charpie avant et après chaque charge. Ne pas utiliser ce sèche-linge si le filtre à peluches n est pas installé. Ne pas réparer ou remplacer un composant quelconque du sèche-linge, ni entreprendre une opération de service, si ce n est spécifiquement recommandé dans ce manuel ou dans un manuel d instructions de réparations destiné à l utilisateur; il est alors essentiel que la personne concernée comprenne ces instructions et soit compétente pour les exécuter. Ne pas utiliser un produit assouplissant de tissu ou des produits pour éliminer la statique à moins qu ils ne soient recommandés par le fabricant du produit assouplissant de tissu ou du produit. Ne pas utiliser la chaleur pour faire sécher des articles fabriqués avec du caoutchouc mousse ou de matériaux semblables. La dernière partie d un programme de séchage par culbutage a lieu sans chaleur (programme de refroidissement) pour faire en sorte que les articles soient laissés à une température qui garantit que les articles ne seront pas endommagés. AVERTISSEMENT: Ne jamais arrêter le séchage par culbutage avant la fin du programme de séchage sauf si tous les articles sont retirés rapidement et répartis pour une dissipation de la chaleur (permet d éviter le risque de combustion spontanée). En cas de coupure de l alimentation électrique, retirer rapidement la charge et l étaler pour éviter tout risque de combustion spontanée. Ne pas laisser la charpie, la poussière, ou la saleté s accumuler autour du système d évacuation ou autour de l appareil. Les ouvertures de ventilation pour l arrivée d air frais dans la pièce et dans le sèche-linge ne doivent pas être obstruées ou scellées. Commande d arrêt d urgence : En cas d urgence, la prise d alimentation secteur doit être retirée. Un nettoyage périodique de l intérieur du sèche-linge et du conduit d évacuation doit être effectué par une personne qualifiée. Voir la section Spécifications électriques dans les instructions d installation pour les instructions de mise à la terre. 25

26 ELIMINATION DU SECHE-LINGE NOMENCLATURE DES MODÈLES : MDG Maytag gaz CS Module de commande électronique avec chute de pièce activé MDE Maytag électrique MN Module de commande électronique sans paiement 18 Numéro de type du modèle 26

27 OUTILS ET PIECES Outillage nécessaire : Clé à tuyau Clé à molette de 203 mm (8") Tournevis à lame plate Tournevis Phillips de 203 mm (8") ou 254 mm (10") (ouverture ou 254 mm (10") jusqu à 25 mm [1"]) Tournevis isolé ou foret Clé à douille hexagonale Clé à douille de 8 mm (5/16") Pince (ouverture Torx T-20 de 25 mm (1") jusqu à 39 mm [1 9 /16"]) Niveau Couteau utilitaire Tourne-écrou de 6 mm (1/4") Cale de bois de 686 mm (27") Pistolet à calfeutrage et Brides de conduit Composé d étanchéité Couteau à mastic composé de calfeutrage des tuyauteries résistant au type (pour l installation d un nouveau de gaz utilisé conduit d évacuation) Lampe de poche Clés plates de 25 mm (1") Règle ou mètre ruban (facultative) Pièces fournies : Patins (4) Pieds du sèche-linge (4) REMARQUE : Le schéma de circuits de ce sèche-linge se trouve à l intérieur du panneau inférieur avant, dans les fiches techniques. Caractéristiques techniques : V, 50 Hz. AC 4575W Poids total : 68 kg max. Capacité de buanderie : 9 kg max. BRUIT : Niveau de pression acoustique, LpA : 58 dba (incertitude, KpA: +/ 10 dba). TORX et T20 sont les marques déposées de Acument Intellectual Properties, LLC. 27

28 DIMENSIONS/DISTANCES DE DEGAGEMENT Dimensions Vue latérale 743 mm (29 1 /4") 648 mm (25 1 /2") Vue arrière 686 mm (27") Électricité Electric 889 mm (35") 210 mm (8 1 /4") 83 mm (3 1 /4") 38 mm (1 1 /2") 140 mm (5 1 /2") 343 mm (13 1 /2") Gaz Gas 279 mm (11") 102 mm (4" dia) 889 mm 1048 mm (35") (41 1 /4") (electric (modèles models) électriques) 940 mm (37") (modèles (gas models) à gaz) 330 mm (13") 83 mm (3 1 /4") 25 mm (1") 260 mm (10 1 /4") Évacuation par le bas 178 mm (7") 359 mm (14 1 /8") Distances de dégagement Encastrement, vue avant Placard, vue latérale 381 mm (15") 356 mm (14") 28 0 mm (0") 0 mm (0") 25 mm (1") 0 mm (0")

29 Exigences de l emplacement EXIGENCES D INSTALLATION POUR LE SECHE-LINGE Le sèche-linge peut être installé dans un sous-sol, une salle de buanderie ou un encastrement. Ce sèche-linge n est pas destiné pour l installation dans une maison mobile. Il faut aussi prendre en compte les exigences d emplacement des appareils voisins. IMPORTANT : Ne pas installer ou remiser le sèche-linge dans un endroit où elle sera exposée aux intempéries. C est à l utilisateur qu incombe la responsabilité de réaliser une installation correcte. Il vous faudra : Une prise électrique reliée à la terre située à moins de 1,8 m (6 pi) de la prise du cordon électrique se trouvant à l arrière du sèche-linge. Voir Spécifications électriques. Un plancher de niveau ayant une pente maximale de 25 mm (1") sous l ensemble du sèche-linge. L installation du sèche-linge sur des surfaces de sol molles, telles que tapis ou surfaces avec sous-couche en mousse n est pas recommandée. Instructions d installation dans un encastrement ou un placard Ce sèche-linge peut être installé dans un encastrement ou un placard. Pour les installations dans un encastrement ou un placard, les distances de dégagement minimales sont indiquées sur l étiquette d avertissement à l arrière du sèche-linge ou à la section Dimensions/Distances de dégagement. Les dimensions d installation sont en millimètres et constituent le minimum applicable. Un espace supplémentaire peut être nécessaire pour faciliter l installation, l entretien et pour observer les codes et règlements locaux. Si une porte de placard est installée, une ouverture d évacuation de l air minimale est nécessaire dans les parties supérieure et inférieure. Les portes à claire-voie offrant des ouvertures équivalentes sont acceptables. Le sèche-linge doit être évacué à l extérieur. Aucun autre appareil utilisant un combustible ne doit être installé dans le même placard. 310 cm 2 (48 po 2 ) Vue de face 155 cm 2 (24 po 2 ) Porte du placard 76 mm (3 po) 76 mm (3 po) Distances de dégagement pour l installation pour le sèche-linge L emplacement doit être assez grand pour permettre d ouvrir complètement la porte du sèche-linge. Prévoir davantage d espace pour faciliter l installation et l entretien. La porte s ouvre à plus de 180. Un espace supplémentaire peut être requis pour les moulures de porte et de plancher et pour les plinthes. Un espace supplémentaire de 25 mm (1") de tous les côtés du sèche-linge est recommandé pour réduire le transfert du bruit. Lors de l installation d un sèche-linge : IMPORTANT : Observer les dispositions de tous les codes et règlements en vigueur. Vérifier les exigences des codes : Certains codes limitent ou n autorisent pas l installation d un sèche-linge dans un garage, un placard ou une chambre à coucher. Communiquer avec l inspecteur en bâtiments local. Sèche-linges à gaz seulement : S assurer que les rebords inférieurs de la caisse ainsi que les côtés arrière et inférieurs du sèche-linge, sont bien dégagés pour permettre une évacuation adéquate de l air de combustion. Voir la section Instructions d installation dans un encastrement ou un placard ci-dessous pour connaître les distances de dégagement minimales. 29