CWS 500N2 SIMULATEUR D'ONDE CONTINUE

Transcription

1 CWS 500N2 SIMULATEUR D'ONDE CONTINUE SELON LES NORMES SUIVANTES... > BMW GS (2001) > DaimlerChrysler DC > DaimlerChrysler DC > DO 160 Section 20 > EN > EN > EN > Fiat > Ford EMC-CS > Ford FMC1278 > GMW 3097 (2001) > GMW 3097 (2004) > IEC > IEC > IEC > IEC > ISO > ISO > MBN > MIL STD 461 D CS 114 > MIL STD 461 E CS 114 >... SYSTÈME D'ESSAI D'INJECTION DE COURANT BULK (BCI) Le système d'essai d'injection Bulk (BCI) est une procédure de test pour prouver l'immunité aux perturbations électriques par bande étroite d'énergie électromagnétique. Le signal de test est injecté au moyen d'une sonde de courant d'injection. Physiquement, la sonde de courant d'injection est un transformateur de courant posé autour de l'installation électrique. Le test d'immunité est réalisé en variant le niveau et la fréquence du signal de test injecté. La méthode de test BCI est généralement utilisée dans l'industrie Automobile, militaire et aéronautique pour tester des composants uniques d'un système complexe. Le CWS 500N2 a été conçu pour être également utilisé pour des tests avec cellules TEM, Stripline et Parallel Plate, ainsi qu'avec des CDNs et pinces électromagnétiques selon les normes EN/IEC POINTS FORTS > Equipement compact > Pour applications BCI, Stripline et cellule TEM > Gamme de fréquence de base 9kHz à 400MHz > Gamme de fréquence extensible jusqu'à 1GHz > Amplificateur 100W classe A intégré jusqu'à 400MHz DOMAINES D'APPLICATION AUTOMOBILE TÉLÉCOMMUNICATION AÉRONAUTIQUE MILITAIRE INDUSTRIE MÉDICAL EM TEST > PAGE 1/5

2 TECHNICAL DETAILS TECHNICAL DETAILS OUTPUT RF output Ouptut power Gain amplifier Output impedance Harmonic distortion N connector at the front panel Built-in amplifier 110 W (nominal) > 50 db 50 ohm < -20 dbc at max. power Insertion loss Approx. 1 db (directional coupler + RF relay) SIGNAL GENERATOR Output impedance Direct RF output dbm to 0 dbm 9 khz to 1 GHz 50 ohm To control an external amplifier MEASUREMENT PM channel power meter up to 1 GHz Forward power Internal power meter #1, -10 dbm to +52 dbm Reverse power Internal power meter #2, -10 dbm to +52 dbm Injected current (Monitor) TIME PARAMETERS Dwell time Pause time Internal power meter #3, -45 dbm to +13 dbm td = 0.3 s - 9,999 s tr = 0/0.3 s - 9,999 s BULK CURRENT INJECTION AS PER ISO As required in ISO , using closed loop or substitution method, up to level 4, 200 ma TEST FREQUENCIES Unmodulated signal Amplitude modulation Pulse modulation DUAL DIRECTIONAL COUPLER Dual directional coupler Power Insertion loss Mainline VSWR 9 khz MHz (built-in amplifier) 9 khz - 1,000 MHz (ext. amplifier) CW (continuous wave) Frequency: 1 Hz to 3,000 Hz, Index: 1% to 95%, Frequency: 1 Hz to 3,000 Hz Index: 10% to 80% Included to measure forward power and reverse power 10 khz to 1 GHz 200 W max. 0.6 db max. 1.1:1 max. BULK CURRENT INJECTION AS PER PSA B217110, EQ IC-08 As required in PSA B217110, EQ IC-08, using the closed loop method, up to level 3, 200 ma BULK CURRENT INJECTION AS PER MIL 461 CS 114 As required in MIL 461 CS 114, using the closed loop method up to curve #5, 109 dbua BULK CURRENT INJECTION AS PER RTCA-DO-160G, SECTION 20 As required in RTCA-DO-160G, Section 20, using closed loop or substitution method, up to 250 ma TEST ROUTINES FOR BULK CURRENT INJECTION ISO MIL 461 CS114 Operation via icd.control Operation via icd.control EM TEST > PAGE 2/5

3 TECHNICAL DATAILS GENERAL DATA TEST ROUTINES FOR IEC Quick Start Service IEC Immediate start; easy-to-use and fast test routine Service, Set-up MEASUREMENTS, IEC Cal in (BNC) Injected current RF indicator LCD INTERFACE Serial interface 1 V - 30 Vrms (emf) all standard test levels are guaranteed with all coupling methods Integrated power meter to record the calibration data of a coupling device Measured by internal power meter LED indicating the RF output status Display of the test level and the preselected frequency value USB Parallel interface IEEE 488, addresses 1-30 Fail 1 Fail 2 BNC input; test will be stopped (active low) BNC input; test status will be saved (max. 10 events) when active low. Test continues GENERAL DATA Dimensions, weight Supply voltage Input power Power factor Fuses Cooling 19"/6 HU, 31.6 kg 115 V or 230 V +10/-15 %, 50/60 Hz Max W Inrush cos(phi) = 0.96 at max. output power as per IEC 555 2x6.3 AT (115 V) or 2x6.3 AT (230 V) Temperature 10 C - 40 C Rel. humidity Atmospheric pressure ACCESSORIES ACCESSORIES Cables icd.control Active cooling, air ventilation Max. 85 %, non-condensing 86 kpa (860 mbar) to 106 kpa (1,060 mbar) N-type coaxial cables to connect the 3dB attenuator and/or the injection probe, BNC-coaxial cable to connect the current monitoring probe, with N-to-BNC adapter Extensive and most versatile remote control and reporting software. The standard library helps to configure the test setup. Multiple interruption functions automated by IEEE instruments or manually. Easy-to-use as well as expandable to complex test routines based on vector definitions. EM TEST > PAGE 3/5

4 ATT3/100 ATT6/80 ATT20/15 ATT20/100 T-50A Calibration CDNs 3dB attenuator, 100 W 6dB attenuator, 80 W 20dB attenuator for current monitor path, the set includes 2 units 20dB attenuator, 100 W for small level RF signals as per MIL STD 461 an DO ohm, 6 W termination resistor Adaptors and cal jigs as per IEC (refer to seperate list) Clamps EM clamp as per IEC Current injection clamps Current monitoring clamps BCI CLAMPS F-120-6A F-120-9A F-130A-1 10 khz MHz, 10 khz MHz, 1 MHz to 400 MHz, F MHz to 1000 MHz, OPTION CURRENT MONITOR CLAMPS F-33-2 Clamp-on monitor probe, 1 khz MHz, F-55 Clamp-on monitor probe, 10 khz MHz, F-65 Clamp-on monitor probe, 100 khz to 1000 MHz, CALIBRATION Connector plate size R-100N R-100N1 R-100A Cal adapters CWS-CAL Size as per IEC Ed.4, The CDN output connector height h defines the connector plate size for the calibration procedure, h = 30 mm => 100 mm x 100 mm h > 30 mm => 150 mm x 150 mm impedance for CDN calibration acc. IEC Ed. 4 Connector plate: 100 mm x 100 mm impedance for CDN calibration acc. IEC Ed. 4 Connector plate: 150 mm x 150 mm impedance with N-type connector for BCI-clamp calibration For all types of CDNs and clamps Basic calibration kit including 1 x R-100N, 1 x 50 cm BNC cable, 1 x plastic case CA EM Ed. 4 Calibration kit for EM 101 as per IEC Ed. 4 2 x R-100N1, 4 x connection rods, 1 x interconnection for rod, 1 x T50, 1 x 90 deg angle for RF input, 1 x 50 cm BNC cable 1 x plastic case FCC-BCICF-1 FCC-BCICF-2 FCC-BCICF-4 (jig) for F-120-6A / F-130-1A probe types (jig) for F-140 probe (jig) for F-120-9A probe EM TEST > PAGE 4/5

5 COMPÉTENCE DANS TOUS LES DOMAINES CONTACTEZ DIRECTEMENT EM TEST Suisse EM TEST (Switzerland) GmbH > Sternenhofstraße 15 > 4153 Reinach > Switzerland Téléphone +41 (0)61/ > Fax +41 (0)61/ Internet: > Allemagne AMETEK CTS Germany GmbH > Lünener Straße 211 > Kamen > Deutschland Téléphone +49 (0)2307/ > Fax +49 (0)2307/17050 Internet: > France EM TEST FRANCE > Le Trident - Parc des Collines > Immeuble B1 - Etage 3 > 36, rue Paul Cézanne > Mulhouse > France Téléphone +33 (0) > Fax +33 (0) Internet: > info@emtest.fr USA / Canada AMETEK Compliance Test Solutions > 52 Mayfield Ave. > Edison > NJ Téléphone +1 (732) Internet: > sales.emtest@ametek.com Chine E & S Test Technology Limited > Rm 913, Leftbank > No. 68 Bei Si Huan Xi Lu > Haidian District > Beijing > P.R. China Téléphone +86 (0) > Fax +86 (0) Internet: > info@emtest.com.cn République de Corée EM TEST Korea Limited > #405 > WooYeon Plaza > #986-8 > YoungDeok-dong > Giheung-gu > Yongin-si > Gyeonggi-do > Korea Téléphone +82 (31) > Fax +82 (31) Internet: > sales@emtest.co.kr Pologne EM TEST Polska > ul. Ogrodowa 31/35, Warszawa > Polska Téléphone +48 (0) Internet: > infopolska.emtest@ametek.com Les informations sur l\'étendue de la livraison, la présentation visuelle et les données techniques correspondent à l\'état de développement du produit au moment de la mise en circulation de la fiche technique. Les données techniques sont susceptibles de changement sans préavis. EM TEST > PAGE 5/5