WARNING. DO NOT RETURN PRODUCT TO THE STORE Individual stores do not stock parts.

Transcription

1 DO NOT RETURN PRODUCT TO THE STORE Individual stores do not stock parts. For prompt, reliable service; please have your assembly manual ready. WARNING This futon has been designed for seating three (3) average adults. To prevent injury and damage to this unit, PROHIBIT jumping on it. This product is designed for home use and not intended for commercial use. Children under the age of 5, small infants and babies must not sleep on this product for safety reasons. Recommended # of people needed for assembly: 1 (however it is always better to have an extra hand). Estimated assembly time is 30 minutes. THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

2 READ BEFORE BEGINNING ASSEMBLY - Read each step carefully. It is very important that each step of instruction is performed in the correct order. If these steps are not followed in sequence, assembly difficulties will occur. - Make sure all parts are included. Most parts are labeled or stamped on the raw edge. HELPFUL HINTS - Move your new furniture carefully, with two people lift and carry the unit to it's new location. - Never push, drag or pull your furniture (especially on carpet). - Additional parts are available for a nominal fee. - Work in spacious area, preferably on a carpet, near the place the unit will be used. - Do not use power tools to assemble your furniture. Power tools may strip or damage the parts.

3

4 --PARTS SEAT Xl LEFT ARM Xl RIGHT ARM Xl HOOK 1 Xl LEGS X4 MIDDLE LEG X2 Xl HOOK2 Xl HOOK3 Xl co PILLOW X2 4/18

5 --HARDWARE I I I HARDWARE PACK WASHER X 10 BOLT 5/16" X 1" X4 BOLT 5/16" X 3/4" X4 SCREW 4X25 mm X2 BOLT 5/16" X 2 1/2" X2 BOLT 5/16" X 3 1/2" XS HEX KEY 5mm Xl BOLT 5/16" X 5 3/4" X4 5/18

6 1 Take out all components, contained in the storage of the SEAT (A), as shown below. 6/18

7 2 Attach (B) and (C) to (A) with the BOLTS (1 & 2) & WASHER (6), as shown in detail. 0 7/18

8 3 Attach (H) and (I) to (D) with BOLTS ( 4), as shown in detail 1 & 3. Attach (G) to (D) with SCREW (5), as shown in detail 2. DETAIL 1 DETAIL 8/18 Xl X4

9 4 Attach (D) to (A, B & C) with BOLTS (3) and SCREW (5), as shown in detail 1 & 2. DETAIL 1 DETAIL 2 D 0 9/18 Xl X4

10 5 Attach (E) to (B & C) with BOLTS (8), as shown in detail 1. Attach (F) to (A), as shown in detail 2. DETAIL 1 DETAIL 2 10/18 X4

11 6 Attach (F) to (A), as shown below. STEP 1 0 STEP /18

12 7 To convert from sofa position to bed position: Pull the backrest in direction of the arrow as far as possible and then release, as shown below. 12/18

13

14 PAGINA04 A) ASIENTO CANTIDAD: 1 B) Brazo izquierdo CANTIDAD: 1 C) BRAZO DERECHO - - CANTIDAD: 1 D) BARRA CANTIDAD: 1 E) F) MEDIA PIERNA CANTIDAD: 2 G) GANCHO CANTIDAD: 1 H) GANCHO CANTIDAD: 1 I) K) ALMOHADA CANTIDAD: 2 PATAS CANTIDAD: 4 GANCHO CANTIDAD: 1 PAGINAOS Paquete de Componentes ) PERNO 5/16" X 3 1/2" CANTIDAD: 8 2) PERNO 5/16" X 2 1/2" CANTIDAD: 2 3) PERNO 5/16" X 1" CANTIDAD: 4 4) PERNO 5/16" X 3/4" CANTIDAD: 4 5) TORNILLO 4X25 mm CANTIDAD: 2 6) LAVADORA CANTIDAD: 10 7) LLAVE DE HEXAGONAL 5mm --- CANTIDAD: 1 8) PERNO 5/16" X 5 3/4" CANTIDAD: 4 PAGINA06 Saque todos las componentes, obtenidos en la memoria del asiento (A) coma se muestra a continuaci6n. PAGINA07 Una la parte "B" Y "C" a la parte "A" con perno (1 Y 2) y arandela (6) coma se muestra a continuaci6n. PAGINAOS Como se muestra en detalle 1 y 3, una la parte "H" Y "I" a la parte "D" con perno (1 y 3); Como se muestra en detalle 2, una la parte "G" a la parte "D" con TORNILLO (5); PAGINA09 Como se muestra en detalle 1 y 2, una la parte "D" a la parte "A" et "B" et "C" con perno (3) y TORNILL0(5); PAGINA 10 Como se muestra en detalle 1, una la parte "E" a la parte "B" y "C" con perno (8); Como se muestra en detalle 2, una la parte "F" a la parte "A"; PAGINA 11 Una la parte "F" a la parte "A" coma se muestra a continuaci6n. PAGINA 12 Para pasar de la posici6n de un sofa a la posici6n de la cama: Tire de la parte de atras en la direcci6n de la flecha lo mas lejos posible y luego puesta en libertad, coma se muestra a continuaci6n. 14/18

15

16

17 PAGE 04 A) SIEGE QUANTITE: 1 B) BRAS GAUCHE - - QUANTITE: 1 C) BRAS DROIT -- - QUANTITE: 1 D) BAR QUANTITE: 1 E) JAMBES QUANTITE: 4 F) PIED CENTRAL - - QUANTITE: 2 G) CROCHET QUANTITE: 1 H) CROCHET QUANTITE: 1 I) CROCHET QUANTITE: 1 K) OREILLER QUANTITE: 2 PAGE OS Paquet de visserie ) BOULON 5/16" X 3 1/2" - QUANTITE: 8 2) BOULON 5/16" X 2 1/2" - QUANTITE: 2 3) BOULON 5/16" X l" QUANTITE: 4 4) BOULON 5/16" X 3/4" ---- QUANTITE: 4 5) VIS 4X25 mm QUANTITE: 2 6) RONDELLE QUANTITE: 10 7) CLE HEXAGONALE 5mm - QUANTITE: 1 8) BOULON 5/16" X 5 3/4" --- QUANTITE: 4 PAGE 06 Sortez taus les composants, contenues dans la memoire du siege (A), comme indique ci-dessous. PAGE 07 Fixer la partie "B" et "C" a la partie "A" avec boulons (1 et 2) et rondelles (6), comme indique ci-dessous. PAGE 08 Tel qu'illustre au detail 1 et 3, fixer la partie "H" et "I" a la partie "D" avec boulons (4). Tel qu'illustre au detail 2, fixer la partie "G" a la partie "D" avec VIS (5). PAGE 09 Tel qu'illustre au detail 1 et 2, fixer la partie "D" a la partie "A","B" et "C" avec boulons (3) et VIS (5). PAGE 10 Tel qu'illustre au detail 1, fixer la partie "E" a la partie "B" et "C" avec boulons (8). Tel qu'illustre au detail 2, fixer la partie "F" a la partie "A". PAGE 11 Fixer la partie "F" a la partie "A", comme indique ci-dessous. PAGE 12 Pour convertir position canape a la position lit: Tirez sur le dossier dans le sens de la fleche autant que possible, puis relachez, comme ci-dessous. 17/18

18 AVANT DE COMMENCER L'ASSEMBLAGE I - Lire attentivement chaque etape avant de debuter. II est tres important que chaque etape de montage soit executes dans le ban ordre pour eviter des difficultes lors de!'assemblage. LES CONSEILS UTILES - Ne jamais pousser, trainer, ou tirer votre mobilier (surtout sur les tapis). - Les pieces supplementaires sont disponibles a un prix nominal. - Assurez-vous que toutes les pieces sont incluses. La plupart des pieces sont etiquetees ou estampees sur le cote non fini. - Travaillez dans un endroit spacieux, preferablement a proximite de l'endroit ou le meuble sera utilise. - Ne pas utiliser d'outils electriques pour assembler votre mobilier. Les outils electriques risquent d'endommager les pieces. 18/18