assembly List of parts

Transcription

1 12V 360W assembly power supply List of parts 220V/110V 12V 360W 30A power supply Plastic cover + LCD Voltmeter IEC power connector + fuse holder and integrated switch 3 x M4x10 screws 2 x M4x10 screws 2 x M4 Nuts 2 x 6cm black wires 2 x 15cm black wires 1 x 15cm green/yellow wires [Not Provided] 1 cruciform screw diver

2 Préparation (vidéo) Make sure the Power supply input power is compatible with your country, for example: Europe : 220V USA : 120V Top Cover (vidéo) Insert 2 M4x6mm screws inside the dedicated holes just next to the voltmeter LCD. The screw head should be inside the cover letting the screw

3 thread out of the cover. Insert the power supply connector inside the dedicated hole and make sure the screws can go threw it.

4 Screw 2 M4 nuts on the M4 Screws thet goes out of the cover as shown on the picture. Here is the inside view of the cover with the M4 screw heads that must be accessible with a screw diver in order to tight them up with their nuts. Ground cable connection

5 (vidéo) Take the 15cm Yellow/Green cable and plug it on the side of the IEC connector the most inside the cover part. Phases (vidéo) wires connection Take the 2 small 6cm long phase wires (here with blue terminals), and connect them just next to the Ground wire (yellow/green).

6 Now connect the wire terminals on the connection pin on the same rows the same way as in the picture. It s more easy to connect them like the picture in a crossed over manner. Connection of the last phases wires (vidéo) Now take the 15 cm wires (here with red terminals) and connect them on the last 2 pins in the bottom row as shown in the picture:

7 Connection of the terminals on the power supply (vidéo) Align the top cover as shown on the picture, with the power supply connector on the right side and the power supply terminals facing you. You can also open the security cover on the power supply in order to have access to the terminals. Ground wire connection

8 (vidéo) Connect the ground wire on the dedicated terminal on the power supply. The corresponding terminal is the 3rd one starting from the right with the following symbol : Here a zoom on the dedicated terminal

9 Phase (vidéo) wires connection Now connect the 2 other phase wires on the terminals left on the right side of the power supply. Connect them on the terminals marked with «N» and «L» letters

10 Voltmeter connection 2 wires must be left, they are the ones of the Digital VoltMeter. On the power supply side, you will find 6 free terminals. They are separated in 2 groups: +V -V The 3 terminals on the left of the power supply (the ones most outside of it) with the «+V» symbol correspond to the +12V output You one You The the V» The need to connect the Red wire from the digital Voltmeter to of the +V terminals. can pick 1 of the 3 terminals on the left as you want. «Black» wire left will have to be connected on one of 3 terminals on the certer of the power supply with the «symbol following pictures show you how to proceed.

11 Zoom on the wires. You can then close the security cover:

12 Output voltage tuning (vidéo) This type of power supply allows to slightly adjust the output voltage using a small trim resistor and a screw diver. In order to prevent you from any electrical hazard, we strongly recommend that you slightly close the cover before switching on the power supply. You might also consider having a quick access tuning trim (here on top of the picture. Before switch the power on, make sure the Power switch is on the «0» position. Also take a moment to check if a fuse is inserted inside the middle cavity (between the power switch and the power plug connector. You can remove the fuse cap with a small flat screw diver.the small chamber containing the fuse should be coming slowly. Check that you have at least 1 fuse at the bottom of the chamber. Push back the fuse cap in position. Now, plug the power cable to the main power grid, and switch the power button on.

13 If everything goes well, the switch button should lit and the LCD voltmeter should show the current voltage output. here 12.4V. This value may vary for you, but you will tune it on the following steps so that you get 12.0

14 Take a screw diver and slowly turn it in one way and on the other way in order to align the power output to 12V. Here is a zoomed picture on the trim resistor.

15 Once properly set you should have a stable 12.0V displayed on the LCD Connection of the 12V output wires (vidéo) Switch off thepower supply Remove the power plug. Take the 4 90cm long wires. 2 Wires must have some Blue or black terminals and 2 other with red terminals. Insert them into the front cover so that the terminals are inside the cover. Also insert the other side of the wires having the red terminals inside the round holes with the «+» marking. Regarding the wires with the blue terminals (or black), inser them inside the holes with

16 marking. All the terminals are inside the plastic cover. The blue wires here have the Red terminals and the brown wires have the blue (or black) terminals

17 Now, connect the wires with the Red termials to the power supply terminals with the «+V» marking. They are mainly the one located on the left of the power supply just next to the green led. The blue terminals wires should be left.connect them on the free terminals on the power supply that should be around the middle with the «-v» marking Closing of the cover (vidéo)

18 Push the plastic covert so that the side holes are aligned with the ones on the power supply. On one side you will need 1 M4 screw. On the other side you will need 2 of them Fix the screws dedicated located. on their

19 Prepare the last 2 M4 screws on the other side of the cover. Congratulation, your power supply is ready to be used. Installation de

20 l alimentation 12V 360W Liste des pièces Bloc d alimentation 220V 12V 360W 30A précédemment monté (voir article) Support plastique + Voltmètre LCD Connecteur d alimentation IEC + porte fusible et interrupteur 3 vis M6x12 3 écrous marteau M6 2 vis M4x10 1 Support plastique d alimentation 1 support plastique latéral [fourni] 1 clef allen [non fourni] 1 tourne vis cruciforme

21 Prenez le support d alimentation qui permet de la soutenir. Insérez 2 jeux de vis M6X12 et écrous marteau. Repérez les deux trous qui serviront à fixer le support.

22 D un côté de l alimentation vous trouverez en bas de l alimentation, seulement 1 seul trou et de l autre côté vous en trouverez 2. Prenez maintenant les 2 vis M4x10mm

23 Positionnez le support de tel manière que les 2 trous prévues pour les vis M4 soient alignés avec ceux de l alimentation Commencez première par vis visser afin stabiliser le support. la de

24 Maintenant visser la deuxième vis. Approchez l alimentation doucement du montant droit de l imprimante. Lorsque les équerres de fixation du montant vertical sont en face de vous, ça correspond à la gauche de l imprimante comme sur la photo. Vous devriez pouvoir glisser les écrou marteau du support dans la gorge du profilé.

25 Une fois dans la gorge, l alimentation devrait être parfaitement parallèle au montant du profilé. Alignez le haut de l alimentation avec le haut du châssis. Si vous avez vissé le support d alimentation correctement dans les étapes précédentes, le bouton et le connecteur d alimentation IEC doivent se trouver au plus près du profilé possible.

26 Maintenant, visser la première vis M6 afin de soutenir le bloc d alimentation. La deuxième vis vient sécuriser le maintien du bloc.

27 Prenez le support plastique qui permet de tenir latéralement le bloc d alimentation. Insérez lui un couple Vis M6x12 et écrous marteau et préparez le comme sur la photo. Vissez-le l intérieur à du présent profilé, à le plus haut possible. Ici il est à ras de l équerre en métal. Le support plastique est souple, donc même si à première vue vous sentez que vous ne pouvez pas le positionner, essayez de le tordre légèrement afin que l extrémité du support se positionne correctement derrière l alimentation.