FORD RANGER BRACKET INSTALLATION PARTS LIST:. 0 X. 0 X. 0 X. 0 X. 0 X. 0 X TOOLS:. 0 X mm Wrench X. 0 X mm Wrench. 00 X. 0 X PASSENGER REAR SHOWN Push Until *Click* Sound STEP A: Tools Required, mm Wrenches Install the bracket as shown. Place one washer 0 on either side of the bracket, then insert the bolt 0 through the forward hole and washers and fasten the nut 0. STEP B: Push the pin until it pops into place making a *CLICK* sound. PASSENGER FRONT SHOWN STEP : Tools Required, mm Wrench Put one washer 0 onto bolt 0 and insert the bolt through the hole in the bracket 0 and into the threaded insert of the front b-post. Tighten with a mm wrench. P/N 0 Rev B
DRIVER REAR SHOWN Push Until *Click* Sound STEP A: Tools Required, Two mm Wrenches Install the bracket as shown. Place one washer 0 on either side of the bracket, then insert the bolt 0 through the forward hole and washers and fasten the nut 0. STEP B: Push the pin until it pops into place making a *CLICK* sound. DRIVER FRONT SHOWN STEP : Tools Required, mm Wrench Put one washer 0 onto bolt 0 and insert the bolt through the hole in the bracket 00 and into the threaded insert of the front b-post. Tighten with a mm wrench. P/N 0 Rev B
INSTALACION DE SOPORTE FORD RANGER PARTS LIST:. 0 X. 0 X. 0 X. 0 X. 0 X. 0 X TOOLS:. 0 X mm Wrench X. 0 X mm Wrench. 00 X. 0 X SE MUESTRA TRASERO DEL PASAJERO Empujar Hasta * Clic * Sonido PASO A: Herramientas requeridas, llaves de - mm Instale el soporte como se muestra. Coloque una arandela 0 a cada lado del soporte, luego inserte el perno 0 a través del orificio delantero y las arandelas y apriete la tuerca 0. PASO B: Empuje el pin hasta que encaje en su lugar haciendo un sonido de * CLICK *. SE MUESTRA EL FRENTE DEL PASAJERO PASO : Herramientas necesarias, llave de mm Coloque una arandela 0 en el perno 0 e inserte el perno a través del orificio en el soporte 0 y en el inserto roscado del poste delantero b. Apriete con una llave de mm. P/N 0 Rev B
SEÑAL TRASERO DEL CONDUCTOR Empujar Hasta * Clic * Sonido PASO A: Herramientas necesarias, dos llaves de mm Instale el soporte como se muestra. Coloque una arandela 0 a cada lado del soporte, luego inserte el perno 0 a través del orificio delantero y las arandelas y apriete la tuerca 0. PASO B: Empuje el pin hasta que encaje en su lugar haciendo un sonido de * CLICK *. SEÑAL FRENTE DEL CONDUCTOR PASO : Herramientas necesarias, llave de mm Coloque una arandela 0 en el perno 0 e inserte el perno a través del orificio en el soporte 00 y en el inserto roscado del poste b frontal. Apriete con una llave de mm. P/N 0 Rev B
INSTALLATION DU SUPPORT DE FORD RANGER PARTS LIST:. 0 X. 0 X. 0 X. 0 X. 0 X. 0 X TOOLS:. 0 X mm Wrench X. 0 X mm Wrench. 00 X. 0 X PASSAGER ARRIERE MONTRÉ Poussez jusqu'au * clic * son ÉTAPE A: Outils nécessaires, clés - mm Installez le support comme indiqué. Placez une rondelle 0 de chaque côté du support, puis insérez le boulon 0 dans le trou avant et les rondelles et serrez l'écrou 0. ÉTAPE B: Poussez la goupille jusqu'à ce qu'elle se mette en place en produisant un son * CLICK *. AVANT DE PASSAGER MONTRÉ ÉTAPE : Outils nécessaires, clé de mm Placez une rondelle 0 sur le boulon 0 et insérez le boulon dans le trou du support 0 et dans l'insert fileté du montant avant. Serrer avec une clé de mm. P/N 0 Rev B
CONDUCTEUR ARRIÈRE MONTRÉ Poussez jusqu'au * clic * son ÉTAPE A: Outils nécessaires, deux clés de mm Installez le support comme indiqué. Placez une rondelle 0 de chaque côté du support, puis insérez le boulon 0 dans le trou avant et les rondelles et serrez l'écrou 0. ÉTAPE B: Poussez la goupille jusqu'à ce qu'elle se mette en place en produisant un son * CLICK *. LE CONDUCTEUR AVANT MONTRÉ ÉTAPE : Outils nécessaires, clé de mm Placez une rondelle 0 sur le boulon 0 et insérez le boulon dans le trou du support 00 et dans l'insert fileté du montant avant. Serrer avec une clé de mm. P/N 0 Rev B