KING WASHINGTON RETROFIT DECORATIVE LED RETROFIT LUMINAIRE Includes: XRAAD Series

Transcription

1 KING WASHINGTON RETROFIT DECORATIVE LED RETROFIT LUMINAIRE Includes: XRAAD Series IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS 1. DANGER RISK OF SHOCK DISCONNECT POWER BEFORE INSTALLATION DANGER RISQUE DE CHOC COUPER L ALIMENTATION AVANT L INSTALLATION 2. This LED retrofit product is UL Classified for use with Washington Series, manufactured by King only. DO NOT install into any other manufacturer s luminaire. To maintain existing Luminaires UL listing, the LED retrofit kit must be UL Classified for use with the manufacturer and model of existing luminaire. Consult CREE Customer support to see if other luminaires are classified to be used with this LED Retrofit kit. Ce produit retrofit LED est classifié UL pour une utilisation avec la série Washington, fabriqué par King seulement. Ne pas installez ce retrofit LED dans le luminaire de tout autre fabricant. Pour maintenir la qualification UL des Luminaires existants, le kit LED retrofit doit être classifié UL pour une utilisation avec le fabricant et le modèle de luminaire existant. Consulter CREE Support Clientèle pour voir si les autres luminaires peuvent être utilisés avec ce retrofit LED. 3. WARNING Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Product must be installed in accordance with NEC or your local electrical code. If you are not familiar with these codes and requirements, contact a qualified electrician. ATTENTION- Risque d'incendie ou de choc électrique. L installation du kit retrofit LED exige la connaissance des systèmes électriques pour luminaires. Si non qualifié, ne tentez pas d'installation. Ce produit doit être installé conformément à NEC ou votre code électrique local. Si vous n'êtes pas familier avec ces codes et ces exigences, veuillez contacter un électricien qualifié. 4. WARNING Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of the LED retrofit kit. Check for enclosed wiring and components. ATTENTION - Risque d'incendie ou de choc électrique. Câblage électriques peuvent être endommagés lors du perçage pour l'installation du kit retrofit LED. Vérifier les fils et composants. 5. WARNING Risk of fire or electric shock. Check the existing wiring for damage before installing retrofit kit. Do not install if existing wires are damaged. ATTENTION- Risque d'incendie ou de choc électrique. Vérifiez si le câblage existant n est pas endommagé avant l'installation du kit retrofit LED. Ne pas installer si des fils sont endommagés. 6. WARNING To prevent wiring damage or abrasion, do not expose wires to the edge of sheet metal or any other sharp objects. ATTENTION - Pour éviter les dégâts de câblage par l'abrasion, ne pas mettre en contact les fils électriques avec des bords de tôle ou d'autres objets pointus. 7. WARNING Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings. ATTENTION - Risque d'incendie ou de choc électrique. Installez ce kit seulement dans les luminaires qui ont les caractéristiques de construction et les dimensions dans les photographies ou les dessins de la page suivante. 8. Do not make or alter any holes in a wiring enclosure or electrical components during the kit installation. Ne pas modifier ou faire de trous dans une boite de câblage ou compartiment électrique lors de l'installation du kit. 9. Ensure that the existing luminaire is installed according to original manufacturer s specification. S'assurer que les luminaires sont installés selon les spécifications du fabricant. 10. Only the holes indicated in the photographs or drawings may be made or altered as a result of the kit installation. Do not leave any other holes open in a wiring enclosure or electrical component. Seulement les trous indiqués dans les photographies ou les dessins peuvent être faits ou altérés pour l installation du kit retrofit LED. Ne laissez aucun trou ouvert dans le compartiment électrique. 11. The retrofit kit contains a universal LED driver and can be operated at voltages of V. Le kit de rénovation contient une alimentation universelle et peut fonctionner à des tensions de V. 12. Once the Retrofit kit is installed, the luminaire can no longer accept HID lamps and shall not be converted back to an HID luminaire. Une fois le kit retrofit LED installé, l'appareil peut ne plus accepter les lampes HID et ne pourra pas être retransformé en luminaire HID. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE CAUTION: WHEN HANDLING LEDS DO NOT CUT PROTECTIVE WRAP AVOID TOUCHING OPTICS INSTALL KIT IN FIXTURE THEN REMOVE PROTECTIVE WRAP BEFORE ENERGIZING LIST OF SUPPLIED COMPONENTS 1. XRA Series Driver Assembly 2. XRA Series LED Module Assembly. 3. (1) Flat Washer 4. (1) Beveled Washer 5. (1) Nut 6. (1) #12-24 X Screw Page 1 of 5

2 RETROFIT FIXTURE INSTALLATION NOTE: Consult your local authority regarding disposal or recycling of removed ballast, capacitor and lamp. 1. Disconnect power to fixture. 2. Verify the existing luminaire model. See Figure 1. FIGURE 4 FIGURE 1 3. Loosen the bolts securing the glass globe to the housing and separate the globe from the housing by carefully lifting it straight up over the lamp. See Figure Remove existing ballast, capacitor, igniter and mounting plate from the Light Engine Assembly Casting and dispose of properly. See Figure 5. NOTE: Save (2) of the large removed screws for mounting the Retrofit Assembly. FIGURE 5 FIGURE 2 4. Loosen the thumb screws and set screws that secure the ballast assembly casting to the housing. See Figure 3. FIGURE 3 7. Remove the Lamp and Lamp Socket from the Light Engine Assembly Casting removing the screws securing it to the casting. After the screws are removed, remove the Lamp and Lamp Socket and dispose of properly. See Figure 6. FIGURE 6 5. Separate the light engine assembly casting from the housing. Disconnect the wire harnesses the Lamp Socket Wires, the Photocell wires, if present, and any other wire connections. See Figure The glass refractor is optional in this model. To remove the refractor, remove the thumb screws securing it to the Light Engine Assembly Casting See FIGURE 7. Page 2 of 5

3 FIGURE 7 FIGURE 9 9. To attach the LED Module Assembly, turn the Light Engine Assembly Casting over to locate the screw hole pattern. NOTE: Depending on the model, the pattern may vary slightly. See Figure 8. FIGURE To prepare the LED Module Assembly, turn over so it is standing up on the heatsink with the Threaded Nipple point up. Place the supplied rotation stop and nylon washer over the Threaded Nipple as shown in Figure 10 and 11. FIGURE CAUTION: WHEN HANDLING LEDS DO NOT CUT PROTECTIVE WRAP AVOID TOUCHING OPTICS INSTALL KIT IN FIXTURE THEN REMOVE PROTECTIVE WRAP BEFORE ENERGIZING 11. Carefully remove the red plastic protective wrap form the LEDs by peeling it back by the label and avoid touching the LEDs FIGURE 8 FIGURE Place the LED Driver Assembly on to the Light Engine Assembly Casting over the selected screw hole pattern and secure with the screws removed in Step. 6. See Figure Lower the attached LED Driver Assembly and Light Engine Assembly Casting over the Threaded Nipple as shown in Figure 12. Page 3 of 5

4 FIGURE See the Electrical Connections sections to wire the luminaire. 18. Once electrical connections are made, insert the Retrofit LED driver Assembly in to the existing housing as shown in Figure 14. FIGURE Using the supplied Beveled Washer and Nut, secure the Retrofit Assembly to the Light Engine Assembly Casting as shown in Figure 12. FIGURE 12 NOTE: If existing fixture has a NEMA Receptacle, take care when lowering the LED Driver Assembly down into the housing. To fit properly, the LED Driver must face away from the NEMA Receptacle. See Figure 15 FIGURE Connect the wire harness coming from the threaded nipple of LED Driver Assembly to the wire harness coming from the terminal block. See Figure 13. FIGURE After Retrofit is in place, re-tighten the thumb screws and set screws that were loosened in Step Carefully replace the globe over the Retrofit Assembly and re-tighten the bolts that were loosened in Step Reconnect power to the fixture. Page 4 of 5

5 SUPPLY WIRING 208/240/480V SUPPLY WIRING ELECTRICAL CONNECTIONS NOTE: Ground connection should include previous luminaire ground as well as ground from retrofit panel. Verify that the supply voltage is within the fixture s voltage rating. 1. For V applications make the following Electrical Connections to the terminal block located on the side of the Retrofit LED Driver Assembly: a. Connect the black lead to the voltage supply lead b. Connect the white lead to the neutral supply lead c. Connect the green or green/yellow ground lead to the supply ground lead d. If Dimming is an option, connect the violet dimming positive lead to the supply dimming positive lead. e. If Dimming is an option, connect the grey dimming negative lead to the supply dimming negative lead FIELD ADJUSTABLE DIMMING NOTE: This luminaire is provided with field adjustable dimming. Luminaires leave the factory adjusted to the maximum setting which is Position 9 as shown in Figure 16 FIGURE V STANDARD FIXTURE WIRING BLACK LINE BLACK GREEN WHITE VIOLET GREY GROUND GREEN NEUTRAL WHITE DIM (+) VIOLET DIM (-) - GREY 2. For 208/240/480V applications, make the following Electrical Connections to the terminal block located on the side of the Retrofit LED Driver Assembly: a. Connect L2 (Hot) supply lead to the black lead. b. Connect L1 (Hot) supply lead to the white lead c. Connect the green or green/yellow ground lead to the supply ground lead d. If Dimming is an option, connect the violet dimming positive lead to the supply dimming positive lead. e. If Dimming is an option, connect the grey dimming negative lead to the supply dimming negative lead 208/240/480V PHASE TO PHASE FIXTURE WIRING (DIMMING OPTIONAL) 1. Locate the luminaires electrical label and verify the maximum wattage available. 2. Establish the desired wattage on the following table and turn the switch to the correlating position. Position 65-69W 97W Input Power Multiplier Input Power Multiplier LINE (L2) LINE BLACK GROUND LINE (L1) VIOLET GREY GROUND GREEN NEUTRAL WHITE DIM (+) VIOLET DIM (-) - GREY (DIMMING OPTIONAL) Page 5 of 5