L examen CE de type des freins de sécurité FRENAX SITEMA par DGUV Test

Dimension: px

Commencer à balayer dès la page:

Download "L examen CE de type des freins de sécurité FRENAX SITEMA par DGUV Test"

Alexis Chartier
il y a 6 ans
Total affichages :

1 Traduction de la version originale allemande L examen CE de type des freins de sécurité FRENAX SITEMA par DGUV Test Après examen détaillé, le bureau de vérification et certification de la DGUV (Assurance sociale allemande des accidents du travail et maladies professionnelles) a délivré l attestation d examen CE de type suivante à SITEMA et a ainsi confirmé la conformité aux exigences de la Directive 2006/42/CE du Parlement européen et du Conseil relative aux machines. N de certification : HSM pour freins de sécurité FRENAX série KSP avec des accessoires voir page 2 sqq. Selon la réglementation actuelle, le certificat a une durée de validité pour une période spécifique à la suite de laquelle un nouveau certificat est délivré. Le premier certificat a été délivré en Veuillez trouver ci-dessous la traduction anglaise de la version allemande d origine. 1/7

Traduction de l interprétation originale en allemand Certificate No. HSM 12 017 dated 14.02.

2 Traduction de l interprétation originale en allemand Certificate No. HSM dated DGUV Test Certificate Name and address of the certificate holder: (client) Name and address of the manufacturer Product description: Type: SITEMA GmbH & Co. KG Im Mittelfeld Karlsruhe - see above - Safety Brakes Series KSP Intended use Test basis: Related test report: Remarks/ Addenda Installation in injection moulding machines conforming to DIN EN 201, presses conforming to DIN EN 289, mechanical presses conforming to DIN EN 692, hydraulic presses conforming to DIN EN 693, or in hydraulic folding presses conforming to DIN EN (for clamping away from the rest position) GS-HSM-02, as of 02/2012 DIN EN 201:2010 Plastics and Rubber Machines Injection Moulding Machines Safety Requirements DIN EN 289:2009 Plastics and Rubber Machines Presses Safety Requirements" DIN EN 692:2009 Machine Tools Mechanical Presses Safety" DIN EN 693:2011 Machine Tools Safety Hydraulic Presses" DIN EN 12622:2010 "Safety of machine tools Hydraulic press brakes No. 046/2012, dated see appendix - The tested model conforms to the requirements stated in 3 Section 1 of the Equipment and Product Safety Act. The tested model conforms to the applicable provisions of the EC Machinery Directive 2006/42/EG. The certificate holder is authorized to attach the DGUV Test mark shown overleaf to products conforming to the tested model, with the addenda quoted under 'Remarks' where appropriate. This certificate will become invalid at the latest on: The Testing and Certification Order of August 2012 makes additional rulings about validity, extensions of validity and other conditions. (Dipl.-Ing. Heinke) Postal address: Postfach Düsseldorf Company address: Graf-Recke-Str Düsseldorf Telephone Fax pz-mhhw@bghm.de 2/7

Traduction de l interprétation originale en allemand Rear of the DGUV Test Certificate DGUV Test mark 1) Certificate number If necessary, the DGUV mark must be provided with an

3 Traduction de l interprétation originale en allemand Rear of the DGUV Test Certificate DGUV Test mark 1) Certificate number If necessary, the DGUV mark must be provided with an addendum corresponding to the details on the certificate. The appearance of the mark will differ from the sample on certificates with supplementary addenda. PZB09MA_D /7

4 Traduction de l interprétation originale en allemand Appendix Certificate No. HSM , dated Name and address of the certificate holder: Product description: SITEMA GmbH & Co. KG Im Mittelfeld Karlsruhe Safety Brakes type KSP Remarks: The manufacturer of the machine must install the Safety Brakes according to the manufacturer's specifications and the requirements of DIN EN 201, DIN EN 289, DIN EN 692, DIN EN 693 respectively DIN EN The manufacturer of the machine must use the control mechanism to prevent a release before the load is secured. The manufacturer of the machine must either select the Safety Brakes so that in the new condition at least 1.5 times the weight of the (actual) load can be supported in the worst case, and provide an automatic device to test for holding force at a sufficiently high frequency or select the Safety Brakes so that in the new condition at least 2 times the weight of the load can be supported in the worst case. If the manufacturer of the machine does not provide an automatic device to test for holding force, he must specify in his operating instructions a deadline for the holding force test which depends on the utilisation of the machine and the requirement rate for the Safety Brakes, within which time the holding force will not decline unacceptably. Test loading: 1.5 times the weight of the (actual) load in the worst case. If the manufacturer of the machine does not provide an automatic device to test for holding force, he must implement a solution whereby the holding force can be checked while the Safety Brake is installed and describe the performance of the holding force test in the operating instructions for the machine. The manufacturer of the machine must install the rod for the Safety Brake so that it is protected from the influence of high-viscosity lubricants or separating agents. The manufacturer of the machine must ensure that the drain of the pilot valve is pressureless. Düsseldorf, (Dipl.-Ing. Heinke) Acting Head Testing and Certification Body 4/7

5 Version originale allemande 5/7

6 Version originale allemande 6/7

7 Version originale allemande 7/7

Documents pareils

Paxton. ins-20605. Net2 desktop reader USB

Paxton. ins-20605. Net2 desktop reader USB Paxton ins-20605 Net2 desktop reader USB 1 3 2 4 1 2 Desktop Reader The desktop reader is designed to sit next to the PC. It is used for adding tokens to a Net2 system and also for identifying lost cards.