ControlNet Modular Repeater Medium-distance Fiber Module (Cat. No RPFM)

Transcription

1 0 Installation Instructions ControlNet Modular Repeater Medium-distance Fiber Module (Cat. No RPFM) Use this document as a guide when you install a ControlNet repeater fiber module for medium distances: To install the module, read these sections: Section Page About The Fiber Module 2 European Union Directive Compliance 3 Mounting The Fiber Module 4 Wiring The Fiber Module 8 CSA Hazardous Location Approval 12 For this information, refer to these sections: Section Page Indicators 10 Mounting Dimensions 11 Specifications 14

2 2 ControlNet Modular Repeater Medium-distance Fiber Module About The Fiber Module Use this module when a medium-distance (distances of 3000m/9843ft) fiber link is required between two ControlNet products. This fiber link provides ground isolation between nodes and is less susceptible to noisy environments than traditional cooper media. Note: The distance that can be supported is dependent on the quality of the fiber, number of splices, and connectors. The total loss of the fiber link must be less than 13.3 db. Typical systems of greater than 3000m are possible. The module provides: two fiber channels activity LED indicators for each fiber channel The figure below identifies the components of the module: Indicators Protective caps Channel 1 fiber port Module locking tab Channel 2 fiber port Right side backplane connector with protective cover The left side of the module (not shown here) also contains a backplane connector M

3 ControlNet Modular Repeater Medium-distance Fiber Module 3 European Union Directive Compliance If this product has the ÎÎ mark, it is approved for installation within the European Union and EEA regions. It has been designed and tested to meet the following directives. EMC Directive The module is tested to meet Council Directive 89/336 Electromagnetic Compatibility (EMC) using a technical construction file and the following standards, in whole or in part: EN EMC Generic Emission Standard, Part 2 Industrial Environment EN EMC Generic Immunity Standard, Part 2 Industrial Environment The module described in this manual is intended for use in an industrial environment. Low Voltage Directive The module is also designed to meet Council Directive 73/23/EEC Low Voltage, by applying the safety requirements of EN Programmable Controllers, Part 2 Equipment Requirements and Tests. For specific information required by EN , see the appropriate sections in that publication. This equipment is classified as open equipment and must be installed (mounted) in an enclosure during operation as a means of providing safety protection.

4 4 ControlNet Modular Repeater Medium-distance Fiber Module Mounting The Fiber Module To mount the module on the DIN rail: 1. Position the module on a 35 x 7.5mm DIN rail at a 30 o angle M 2. Hook the lip on the rear of the module onto the top of the DIN rail, and rotate the module onto the rail M

5 ControlNet Modular Repeater Medium-distance Fiber Module 5 3. Press the module down onto the DIN rail until flush. The locking tab should snap into position and lock the module to the DIN rail. 4. If the module does not snap into position, use a screwdriver or similar device to move the locking tab down while pressing the module flush onto the DIN rail. Release the locking tab to lock the module in place. If necessary, push up on the locking tab to lock.

6 6 ControlNet Modular Repeater Medium-distance Fiber Module 5. Remove the protective backplane cap as shown in Removing the Protective Caps on page Once attached to the DIN rail, slide modules to the left to mate with the repeater adapter or another repeater module M! ATTENTION: Make certain that the adapter and repeater modules are secured together with DIN rail anchors. Failure to do so may result in the loss of communications and/or cause damage to the modules. The total number of modules that can be attached to the repeater adapter can not exceed four or the total power consumption of the modules can not exceed 5VDC, whichever comes first. Important: If you exceed the module or power limit, you may cause damage to the repeater adapter and modules. Important: If this is the right most module, a DIN rail latch must be used on the right side of the fiber module. 7. Connect the module wiring as shown in Wiring The Fiber Module on page 8.

7 ControlNet Modular Repeater Medium-distance Fiber Module 7 Removing the Protective Caps 1. Remove the protective caps from the fiber channels that will be used. 2. Save the caps for future use. Protective backplane cap DIN rail Protective cap The left side of the module (not shown here) also contains a backplane connector M If: a channel is not going to be used another module will be connected to the right backplane connector a module will not be connected to the right backplane connector Then: keep protective caps on channels to protect unit from dust. remove the protective backplane cap and save cap for future use. leave the backplane cap attached.

8 8 ControlNet Modular Repeater Medium-distance Fiber Module Wiring The Fiber Module If only one channel is wired, you can use Channel 1 or Channel 2. To wire the module for Channel 1: 1. Connect to Receive ST. a. Align the knob of the ST cable connector with the groove of the ST module connector, and insert the connector into A. Channel 1 Channel 2 A B (transmit) (receive) M b. Twist the Receive ST connector until the bayonet lug is locked into place. 2. To connect to Transmit ST into B, repeat Step 1.

9 ControlNet Modular Repeater Medium-distance Fiber Module 9 To wire the module for Channel 2: 1. Repeat the steps for Channel 1 and refer to the following figure RPA 9904 RPFM CH1 CH2 A B A B 9904 RPA 9904 RPFM CH1 CH2 A B A B OR Important: Important: Be sure the fiber connected to A(receive) on one 9904 RPFM is connected to B(transmit) on the other 9904 RPFM. You can use Channel 1 or Channel 2 on either card. Never connect the fiber cable between Channel 1 or Channel 2 on the same repeater module, even between channels from different modules on the same repeater.! Warning: Do not look directly into the fiber ports. Light levels may cause damage to eyesight.

10 10 ControlNet Modular Repeater Medium-distance Fiber Module Indicators The figure below identifies indicators on the module: Channel 1 status Channel 2 status The table below defines Channel 1 and Channel 2 (individually) status indications: Status Indicator Off Green Flashing Green/Off Probable Cause No power or module is faulted Channel operational No data activity on associated channel

11 ControlNet Modular Repeater Medium-distance Fiber Module 11 Mounting Dimensions The figure below provides mounting dimensions for the module: 4.44 in. (111 mm) 2.76 in. (69 mm) 4.0 in. (100 mm) 3.6 in. (90 mm) in. (101.2 mm) Specifications

12 12 ControlNet Modular Repeater Medium-distance Fiber Module CSA Hazardous Location Approval CSA certifies products for general use as well as for use in hazardous locations. Actual CSA certification is indicated by the product label as shown below, and not by statements in any user documentation. Example of the CSA certification product label To comply with CSA certification for use in hazardous locations, the following information becomes a part of the product literature for CSA-certified industrial control products. This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D, or non-hazardous locations only. The products having the appropriate CSA markings (that is, Class I Division 2, Groups A, B, C, D), are certified for use in other equipment where the suitability of combination (that is, application or use) is determined by the CSA or the local inspection office having jurisdiction. Important: Due to the modular nature of a programmable control system, the product with the highest temperature rating determines the overall temperature code rating of a programmable control system in a Class I, Division 2 location. The temperature code rating is marked on the product label as shown. Temperature code rating Look for temperature code rating here The following warnings apply to products having CSA certification for use in hazardous locations. ATTENTION: Explosion hazard Substitution of components may impair suitability for Class I, Division 2.! Do not replace components unless power has been switched off or the area is known to be non-hazardous. Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous. Do not disconnect connectors unless power has been switched off or the area is known to be non-hazardous. Secure any user-supplied connectors that mate to external circuits on a product using screws, sliding latches, threaded connectors, or other means such that any connection can withstand a 15 Newton (3.4 lb.) separating force applied for a minimum of one minute. CSA logo is a registered trademark of the Canadian Standards Association.

13 ControlNet Modular Repeater Medium-distance Fiber Module 13 Approbation d utilisation dans des emplacements dangereux par la CSA La CSA certifie les produits d utilisation générale aussi bien que ceux qui s utilisent dans des emplacements dangereux. La certification CSA en vigueur est indiquée par l étiquette du produit et non par des affirmations dans la documentation à l usage des utilisateurs. Exemple d étiquette de certification d un produit par la CSA Pour satisfaire à la certification de la CSA dans des endroits dangereux, les informations suivantes font partie intégrante de la documentation des produits industriels de contrôle certifiés par la CSA. Cet équipement convient à l utilisation dans des emplacements de Classe 1, Division 2, Groupes A, B, C, D, ou ne convient qu à l utilisation dans des endroits non dangereux. Les produits portant le marquage approprié de la CSA (c est à dire, Classe 1, Division 2, Groupes A, B, C, D) sont certifiés à l utilisation pour d autres équipements où la convenance de combinaison (application ou utilisation) est déterminée par la CSA ou le bureau local d inspection qualifié. Important: Par suite de la nature modulaire du système de contrôle le produit ayant le taux le plus élevé de température détermine le taux d ensemble du code de température du système de contrôle d un programmable dans un emplacement de Classe 1, Division 2. Le taux du code de température est indiqué sur l étiquette du produit. Taux du code de température Le taux du code de température est indiqué ici Les avertissements suivants s appliquent aux produits ayant la certification CSA pour leur utilisation dans des emplacements dangereux.! AVERTISSEMENT: Risque d explosion La substitution de composants peut rendre ce matériel inacceptable pour lesemplacements de Classe I, Division 2. Couper le courant ou s assurer quel emplacement est désigné non dangereux avant de remplacer lescomposants. Avant de débrancher l équipement, couper le courant ou s assurer que l emplacement est désigné non dangereux. Avant de débrancher les connecteurs, couper le courant ou s assurer que l emplacement est reconnu non dangereux. Attacher tous connecteurs fournis par l utilisateur et reliés aux circuits externes d un appareil à l aide de vis, loquets coulissants, connecteurs filetés ou autres moyens permettant aux connexions de résister à une force de séparation de 15 newtons (3,4 lb. - 1,5 kg) appliquée pendant au moins une minute. Le sigle CSA est la marque déposée de l Association des Standards pour le Canada.

14 14 ControlNet Modular Repeater Medium-distance Fiber Module Specifications The table below provides specifications for the module: Communication Rate Indicators Backplane Power Requirements Environmental Conditions Operating Temperature Storage Temperature Relative Humidity Shock Operating Non-operating Vibration Fiber Type Fiber Termination Type Fiber Operating Wavelength Optical Power Budget Agency Certification (when product is marked) 5M bits/s Channel 1 Status Green Channel 2 Status Green 400 ma 0 to 60 o C (32 to 140 o F) 40 to 85 o C ( 40 to 185 o F) 5 to 95% non-condensing 30 g peak acceleration, 11( 1)ms pulse width 50 g peak acceleration, 11( 1)ms pulse width Tested Hz per IEC /125 micron ST (plastic or ceramic) 1300 nm 13.3 db ➀ certified listed ÎÎmarked for all applicable directives certified Class 1 Div2 Groups A,B,C,D Hazardous Locations ➀ This includes all loss associated with the fiber link, including: splices, fiber attenuation, bulkhead connectors, and the 9904 RPFM ST terminations. ControlNet is a trademark of ControlNet International ST is a registered trademark of AT&T February 1998