Washing Machine user manual

Transcription

1 WF42H5200A* WF42H5100A* WF42H5000A* Washing Machine user manual This manual is made with 100% recycled paper. imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service or accessory parts, please register your product at or contact SAMSUNG ( )

2 contents installing your washer operating instructions washing a load of laundry Unpacking your washer 11 Overview of your washer 12 Electrical 12 Grounding 12 Water 13 Drain facility 13 Flooring 13 Location considerations 13 Alcove or closet installation 13 Undercounter installation (washer only) 14 With optional pedestal base or stacking kit 15 Important note to installer 15 Installation flow chart Loading your washer 18 Washing clothes: Basic Instructions Overview of the control panel 21 Child Lock 22 Garment+ 22 Delay End 22 My Cycle 23 Sound 23 Smart Care 24 Washing clothes using the cycle selector 25 Using steam wash 25 ATC (Auto Temperature Control) 26 Detergent use 26 Features maintaining your washer troubleshooting appendix Cleaning the exterior 28 Cleaning the interior 28 Cleaning the dispensers 28 Storing your washer 29 Cleaning the debris filter 30 Cleaning the door Diaphragm 30 Preserving the top cover and the front frame 31 Self Clean+ Check these solutions if your washer 34 Information codes Fabric care chart 37 Cycle chart 39 Helping the environment 39 Declaration of conformity 39 Specification 2_English

3 safety information Congratulations on your new Samsung washer. This manual contains important information on the installation, use, and care of your appliance. Please take time to read this manual to take full advantage of your washer s many benefits and features. What you need to know about safety instructions Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating your washer. Important safety symbols and precautions What the icons and signs in this user manual mean: WARNING Hazards or unsafe practices that may result in severe personal injury or death. To reduce the risk of fire, explosion, electric shock, or personal injury when using your washer, follow these basic safety precautions: CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage. Do NOT attempt. Do NOT disassemble. Do NOT touch. Follow directions explicitly. Unplug the power plug from the wall socket. Make sure the machine is grounded to prevent electric shock. Call the service center for help. Note These warning signs are here to prevent injury to you and others. Please follow them explicitly. After reading this section, keep it in a safe place for future reference. Read all instructions before using the appliance. SAVE THESE INSTRUCTIONS English _3

4 safety information WARNING WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using the appliance. 2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode. 3. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children. 4. Before the appliance is removed from service or discarded, remove the door to the washing or drying compartment. 5. Do not reach into the appliance if the drum is moving. 6. Do not install or store this appliance where it will be exposed to the weather. 7. Do not tamper with controls. 8. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published userrepair instructions that you understand and have the skills to carry out. 9. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode. 10. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washer or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time. WARNING State of California Proposition 65 Warnings: WARNING: This product contains chemicals known to the State of California to cause cancer and reproductive toxicity. SAVE THESE INSTRUCTIONS 4_English

5 WARNING SEVERE WARNING SIGNS FOR INSTALLATION Plug the power cord into an AC 120 V / 60 Hz / 15 A wall socket or higher and use the socket for this appliance only. In addition, do not use an extension cord. - Sharing a wall socket with other appliances using a power strip or extending the power cord may result in electric shock or fire. - Do not use an electric transformer. It may result in electric shock or fire. - Ensure that the power voltage, frequency and current are the same as those of the product specifications. Failing to do so may result in electric shock or fire. The installation of this appliance must be performed by a qualified technician or service company. - Failing to do so may result in electric shock, fire, an explosion, problems with the product, or injury. Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis. - Unplug the power plug and clean it with a dry cloth. - Failing to do so may result in electric shock or fire. Plug the power plug into the wall socket in the right direction so that the cord runs towards the floor. - If you plug the power plug into the socket in the opposite direction, the electric wires within the cable may be damaged and this may result in electric shock or fire. This appliance must be properly grounded. Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line. - This may result in electric shock, fire, an explosion, or problems with the product. - Never plug the power cord into a socket that is not grounded correctly and make sure that it is in accordance with local and national codes. Do not install this appliance near a heater or inflammable material. Do not install this appliance in a humid, oily or dusty location, in a location exposed to direct sunlight and water (rain drops). Do not install this appliance in a location where gas may leak. - This may result in electric shock or fire. Plug the power plug into the wall socket firmly. Do not use a damaged power plug, damaged power cord or loose wall socket. - This may result in electric shock or fire. Do not pull or excessively bend the power cord. Do not twist or tie the power cord. Do not hook the power cord over a metal object, place a heavy object on the power cord, insert the power cord between objects, or push the power cord into the space behind the appliance. - This may result in electric shock or fire. Do not pull the power cord when unplugging the power plug. - Unplug the power plug by holding the plug. - Failing to do so may result in electric shock or fire. SAVE THESE INSTRUCTIONS English _5

6 safety information When the power plug or power cord is damaged, contact your nearest service center. CAUTION CAUTION SIGNS FOR INSTALLATION WARNING This appliance should be positioned in such a way that it is accessible to the power plug. - Failing to do so may result in electric shock or fire due to electric leakage. Install your appliance on a level and hard floor that can support its weight. - Failing to do so may result in abnormal vibrations, noise, or problems with the product. Unplug the power plug when the appliance is not being used for long periods of time or during a thunder/lightning storm. - Failing to do so may result in electric shock or fire. SEVERE WARNING SIGNS FOR USING If the appliance is flooded, cut the power immediately and contact your nearest service center. If the appliance generates a strange noise, a burning smell or smoke, unplug the power plug immediately and contact your nearest service center. - Failing to do so may result in electric shock or fire. In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without touching the power plug. Do not touch the appliance or power cord. - Do not use a ventilating fan. - A spark may result in an explosion or fire. Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or other flammable or explosive substances. - This may result in electric shock, fire or an explosion. Do not open the washer door by force while it is operating (high-temperature washing/ drying/spinning). - Water flowing out of the washer may result in burns or cause the floor to be slippery. This may result in injury. - Opening the door by force may result in damage to the product or injury. Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the washer before using it. Do not insert your hand under the washer. - This may result in injury. SAVE THESE INSTRUCTIONS 6_English

7 Do not touch the power plug with wet hands. - This may result in electric shock. Do not turn the appliance off by unplugging the power plug while an operation is in progress. - Plugging the power plug into the wall socket again may cause a spark and result in electric shock or fire. Keep all packaging materials well out of the reach of children, as packaging materials can be dangerous to children. - If a child places a bag over their head, they may result in suffocation. Do not let children or infirm persons use this washer unsupervised. - Failing to do so may result in electric shock, burns or injury. Do not insert your hand or a metal object under the washer while it is operating. - This may result in injury. Make sure the detergent drawer is closed before you put laundry into the washer or remove laundry from the washer. - If the detergent drawer is open, you could strike the drawer with your head and injure yourself. Do not attempt to repair, disassemble, or modify the appliance yourself. - Do not use any fuse ( such as cooper, steel wire, etc.) other than the standard fuse. - When repairing or reinstalling the appliance is required, contact your nearest service center. - Failing to do so may result in electric shock, fire, problems with the product, or injury. If any foreign substance such as water has entered the appliance, unplug the power plug and contact your nearest service center. - Failing to do so may result in electric shock or fire. When the water supply hose comes loose from the faucet and floods the appliance, unplug the power plug. - Failing to do so may result in electric shock or fire. If any foreign substance enters the appliance, unplug the power plug and contact you nearest service center. - Failing to do so my result in electric shock or fire. SAVE THESE INSTRUCTIONS English _7

8 safety information CAUTION CAUTION SIGNS FOR USING When the washer is contaminated by a foreign substance such as detergent, dirt, food waste, etc., unplug the power plug and clean the washer using a damp and soft cloth. - Failing to do so may result in discoloration, deformation, damage or rust. The front glass may be broken by a strong impact. Take care when using the washer. - When the glass is broken, it may result in injury. After a water supply failure or when reconnecting the water supply hose, open the faucet slowly. Open the faucet slowly after a long period of non-use. - The air pressure in the water supply hose or the water pipe may result in damage to a part or in water leakage. If a drain error occurs during an operation, check if there is a draining problem. - If the washer is used when it is flooded because of a draining problem, it may result in electric shock or fire due to electric leakage. Insert the laundry into the washer completely so that laundry does not get caught in the door. - If laundry gets caught in the door, it may result in damage to the laundry or the washer, or result in water leakage. Ensure that the faucet is turned off when the washer is not being used. - Ensure that the screw on the water supply hose connector is properly tightened. - Failing to do so may result in property damage or injury. Take care that the Rubber Seal and the Front Door Glass are not contaminated by a foreign substance (e.g. waste, thread, hair, etc.). - If a foreign substance is caught in the door or the door is not completely closed, it may cause a water leakage. Open the faucet and check if the water supply hose connector is firmly tightened and that there is no water leaking before using the product. - If the screws or the water supply hose connector are loose, it may result in water leak. The product you have purchased is designed for domestic use only. The use for business purposes qualifies as product misuse. In this case, the product will not be covered by the standard warranty provided by Samsung and no responsibility can be attributed to Samsung for malfunctions or damages resulting from such misuse. If the wash is not started and the laundry is left for a period of time after you have added detergent or applied stain remover or pre-treatment onto the laundry, the laundry may be discolored. Select the recommended cycle and temperature on the basis of the laundry items, sort the laundry by color on the basis of its colorfastness and select the appropriate cycle. Make sure that foreign objects such as pins, buttons and coins are removed from clothing items when adding laundry to the washer. Wash dirty laundry separately from relatively clean items and wash fragile items separately from tougher textiles. If an item is stained, wash it as soon as possible. Use stain remover or detergent only after testing the colorfastness of the item by applying a small quantity to an inside seam. SAVE THESE INSTRUCTIONS 8_English

9 Do not stand on top of the appliance or place objects (such as laundry, lighted candles, lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance. - This may result in electric shock, fire, problems with the product, or injury. Do not operate the appliance with wet hands. - This may result in electric shock. Do not spray volatile material such as insecticide onto the surface of the appliance. - As well as being harmful to humans, it may also result in electric shock, fire or problems with the product. Do not place an object that generates a electromagnetic field near the washer. - This may result in injury due to a malfunction. Since the water drained during a high-temperature wash or drying cycle is hot, do not touch the water. - This may result in burns or injury. Do not wash, spin or dry water-proof seats, mats or clothing (*). - Do not wash thick, hard mats even if the washer mark is on the care label. - This may result in injury or damage to the washer, walls, floor or clothing due to abnormal vibrations. * Woolen Bedding, rain covers, fishing vests, ski pants, sleeping bags, diaper covers, sweat suits, and bicycle, motor cycle, car covers, etc. Do not operate the washer when the detergent box is removed. - This may result in electric shock or injury due to water leakage. Do not touch the inside of the tub during or just after drying as it is hot. - This may result in burns. Do not insert your hand into the detergent dispenser after opening it. - This may result in injury as your hand may be caught. Do not place any objects (such as shoes, food waste, animals) other than laundry into the washer. - This may result in damage to the washer, or injury and death in the case of pets due to the abnormal vibrations. Do not press the buttons using sharp objects such as pins, knifes, fingernails, etc. - This may result in electric shock or injury. Do not wash laundry contaminated by oils, creams or lotions usually found in skincare shops or massage clinics. - This may result in the rubber seal becoming deformed and water leakage. Do not leave metal objects such as a safety pin or hair pin, or bleach in the tub for long periods of time. - This may cause the tub to rust. - If rust starts appearing on the surface of the tub, apply a cleansing agent (neutral) to the surface and use a sponge to clean it. Never use a metal brush. SAVE THESE INSTRUCTIONS English _9

10 safety information WARNING Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry contaminated by dry cleaning detergent. - This may result in spontaneous combustion or ignition due to the heat of the oxidation of the oil. Do not use hot water from water cooling/heating devices. - This may result in problems with the washer. Do not use natural hand-washing soap for the washer. - If it hardens and accumulates inside the washer, it may result in problems with the product, discoloration, rust or bad odors. Do not wash large laundry items such as Bedding in the washing net. - Failing to do so may result in injury due to abnormal vibrations. - Place smaller items, such as lace socks and lingerie in the washing net. Do not use hardened detergent. - If it accumulates inside the washer, it may result in water leakage. Do not wash throw rugs or doormats. - If you wash throw rugs or doormats, the sand will accumulate inside the washer. It may result in error such as no draining. Take care that children s fingers are not caught in the door when closing it. This may result in injury. SEVERE WARNING SIGNS FOR CLEANING Do not clean the appliance by spraying water directly onto it. Do not use the strong acid cleaning agent. Do not use benzene, thinner or alcohol to clean the appliance. - This may result in discoloration, deformation, damage, electric shock or fire. Before cleaning or performing maintenance, unplug the appliance from the wall socket. - Failing to do so may result in electric shock or fire. SAVE THESE INSTRUCTIONS 10_English

11 installing your washer Unpacking your washer Unpack your washer and inspect it for shipping damage. Make sure you have received all the items shown below. If your washer was damaged during shipping, or you do not have all of the items, contact SAMSUNG ( ). To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit. WARNING Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene, etc.) well out of the reach of children. Overview of your washer Hot water supply hose Cold water supply hose 01 Installing your washer Detergent drawer Control panel Door Drain Hose Tub Debris filter Drain tube Filter cover Adjustable legs Wrench Bolt Hole Covers Water Supply Hoses Hose Guide Plastic Zip Hose Tie anti-slip pads * Bolt hole covers : The number of bolt hole covers depends on the model (3~6 covers). English _11

12 installing your washer BASIC LOCATION REQUIREMENTS Electrical 120 Volt 60 Hz 15 AMP fuse or circuit breaker Individual branch circuit serving only your washer is recommended. Your washer is equipped with a power cord. CAUTION NEVER USE AN EXTENSION CORD. Grounding ELECTRICAL GROUNDING IS REQUIRED FOR THIS APPLIANCE. This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a power cord having a three-prong grounding plug for use in a properly installed and grounded three-prong outlet. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. An improperly connected equipment-grounding conductor can increase the risk of electrical WARNING shock. Check with a qualified electrician or serviceman if you are not sure whether the appliance is properly grounded. Do not modify the plug provided with the appliance if it does not fit the outlet, have a proper outlet installed by a qualified electrician. IMPORTANT SAFETY PRECAUTIONS To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No. 70 Latest Revision and local codes and ordinances. It is the personal responsibility of the appliance owner to provide adequate electrical service for this appliance. NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR CAUTION HOT WATER PIPES. Water Using bad quality water may cause the water supply valve to operate abnormally. To correctly fill your washer in the proper amount of time, water pressure of psi ( kpa) is required. Water pressure less than 20 psi may cause water valve failure, may not allow the water valve to shut off completely, or may extend the fill time beyond what your washer controls allow, causing your washer to turn off. A time limit is built into the controls to prevent extensive flooding in your home if an internal hose becomes loose. The water faucets must be within 4 feet / 122 cm of the back of your washer to match the inlet hoses provided with your washer. Accessory inlet hoses are available in various lengths up to 10 feet/305 cm for faucets that are further away from the back of your washer. To avoid the possibility of water damage: Have water faucets easily accessible. Turn off faucets when the washer is not in use. Periodically check that there is no leakage from the water inlet hose fittings. CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS. WARNING 12_English

13 Drain facility The recommended height of the standpipe is 18 in/46 cm. The drain hose must be routed through the drain hose clip to the standpipe. The standpipe must be large enough to accept the outside diameter of the drain hose. The drain hose is attached at the factory. Flooring For best performance, you must install your washer on a solidly constructed floor. Wood floors may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting and soft tile surfaces are contributing factors to vibration which can cause your washer to move slightly during the spin cycle. Never install your washer on a platform or weakly supported structure. Location considerations Do not install your washer in areas where water may freeze, since your washer will always retain some water in its water valve, pump, and hose areas. Freezing water can damage the belts,the pump, hoses and other components. Alcove or closet installation 01 Installing your washer MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS: Sides 1 in / 25 mm Top 17 in / 432 mm Rear 5.9 in / 150 mm Closet Front 2 in / 51 mm If the washer and dryer are installed together, the closet front must have at least a 72 in² (465 cm²) unobstructed air opening. Your washer alone does not require a specific air opening. A. Recessed area A 1 in. (2.5 cm) B 17 in. (43.2 cm) 1 in. (2.5 cm) 27 in. (68.6 cm) 27 in. (68.6 cm) 1 in. (2.5 cm) 2 in. (5 cm) 33 in. (83.8 cm) 5.9 in. (15 cm) B. Side view - closet or confined area Undercounter installation (washer only) 40 in. (101.6 cm) 1 in. (2.5 cm) 27 in. (68.6 cm) 1 in. (2.5 cm) English _13

14 installing your washer With optional pedestal base or stacking kit Required Dimensions for Installation With Pedestal 51.2 in. (130 cm) to clear open door 38.7 in. (98.4cm) 33 in. (83.8 cm) 5.9 in. (15 cm) 27 in. (68.6 cm) 53.4 in. (135.6 cm) 48 in.² * (310 cm²) 3 in. (7.6 cm) 5 in. (12.7 cm) 24 in.² * (155 cm²) Closet or Door 3 in. (7.6 cm) 1 in. (2.5 cm) Required Dimensions for Installation With Stacking Kit 33 in. (83.8 cm) 5.9 in.** (15 cm) 6 in. * (15.2 cm) 77.5 in. (197 cm) 1 in. (2.5 cm) 27 in. (68.6 cm) * Required spacing ** external exhaust elbow requires additional space. 14_English

15 Important note to installer Please read the following instructions carefully before installing the washer. These instructions should be retained for future reference. We recommend you hire a professional to install this washer. Installation flow chart Selecting a location Please check again before steps. Adjusting the levelling feet Removing the shipping bolts (*Drum only) Powering your washing machine Connecting the water and the drain [Running a test cycle] Run a test cycle (Rinse+Spin) with small amount of laundary (about 4~5 Towels) 01 Installing your washer Yes Does your washer have excess vibration or noise? No Running a Calibration mode (Refer to the following description) Finish the installation STEP 1 Removing the Shipping Bolts Before using your washer, you must remove all shipping bolts from the back of the unit. 1. Loosen all the bolts with the supplied wrench. 2. Slide the bolt and spacer up and remove the bolt with the spacer through the hole in the rear wall of your washer. Repeat for each bolt. 3. Cover the holes with the supplied Bolt Hole Covers (See page 11). 4. Keep the shipping bolts and spacers for future use. STEP 2 Selecting a Location Before you install your washer, make sure the location: Has a hard, level surface. Is away from direct sunlight. Has adequate ventilation. Will not freeze (tempuratures are never below 32 F or 0 C). Is away from heat sources such as oil or gas. Has enough room for the power cord. Doesn t have any carpeting that will obstruct ventilation openings. English _15

16 installing your washer STEP 3 Installing your Washer 1. If you use a standpipe, make sure the connection between the drain hose and the standpipe is NOT airtight. The standpipe must be at least 18 in or 46 cm high. You must always exercise caution to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way by elbows, couplings, or excessive 96 Max length. For situations where the drain hose cannot be conveniently elevated to at least 18 in or 46 cm, the drain hose must be supported. If drain hose is installed below 18 (46cm), water can be drained in cycle working cause of siphon phenomenon. It causes the washer to nf error. Drain Hose can be installed until 96 (245cm) maximum. But drain capability can be reduced at this height. It causes the washer to have an odor because of remaining water in the drain system. Connect the hose guide within 6 (15cm) from the end of the drain hose. If the drain hose is extended more than 6 (15cm) beyond the end of the hose guide, mold or microorganisms could spread to the inside of the washer. Laundry tub Hose 18 Min retainer 96 Max 18 Min Tie strap Cold Standpipe Hot 2. Check the inlet hose to ensure a washer is inside each fill hose. Thread the inlet hoses to the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and attach each fill hose to the water valve. Make sure the hose with Hot printed on it is attached to the HOT faucet. Tighten by hand until snug, then two-thirds of a turn with pliers. For correct water use, connect both HOT and COLD water valves. If either or both are not connected, an nf (no fill) error can occur. Rubber Washer 3. Turn on the HOT and COLD water supply and check the water valve and the water supply connections for leaks. Cold printed Hot printed 16_English

17 4. Slide your washer into position. 5. Level your washer by turning the leveling legs in or out as necessary by hand or by using the wrench included with your washer. When your washer is level, tighten the locking nuts using the wrench or (-) flathead screwdriver. 6. Plug the power cord into a 3-Prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded receptacle. Your washer must be leveled on all four sides. A carpenter s level should be used on all four corners of your washer. We recommend you recheck your washer after a dozen or so washes to make sure it s still level. Locking Nut Levelling Leg 01 Installing your washer Avoid damage to the legs. Do not move the washer unless the Locking-nuts are fastened to the bottom of the washer. Test run Make sure that you install your washing machine correctly by running the Rinse+Spin cycle after the installation is complete. STEP 4 Calibration mode Your Samsung washing machine automatically detects the weight of the laundry. For more accurate weight detection, please run Calibration Mode after the installation. To run Calibration Mode, follow these steps: 1. Turn on the washer. 2. Press the Temp. button and Delay End button simultaneously for at least 3 seconds. 3. Remove any contents in the tub and close the door. 4. Press the Start/Pause button. 5. The drum rotates clockwise and counterclockwise for approximately 3 minutes. 6. When Calibration Mode is finished, the En/End appears on the display and the washing machine turns off automatically. The washing machine is now ready for use. English _17

18 operating instructions WARNING To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. Loading your washer You can fill the tub with dry, unfolded clothes, but DO NOT OVERLOAD the tub. No more than 3/4 full. Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or wrinkling of the load. Wash delicate items such as bras, hosiery, and other lingerie in the Delicates cycle with similar lightweight items. When washing big bulky items or a few smaller items that don t fill the tub completely a rug, a pillow, stuffed toys, or one or two sweaters, for example add a few towels to improve tumbling and spin performance. During the spin cycle, the washer may add additional water to redistribute the clothes and correct an inbalance inside the drum. To ensure good cleaning result when washing heavily soiled loads, do not overload your washer. When the light is ON (see page 22), you can add or remove laundry items during a wash. 1. Press the Start/Pause Button. 2. Wait for the Door Lock light to go out (5 seconds). 3. Add the item, close the door, and press the Start/Pause Button. After a 10-second pause, the cycle will resume. To ensure thorough cleaning, add items within five minutes of starting the wash cycle. Washing clothes: Basic Instructions 1. Press the Power button, open the door, and then load the washer. 2. Close the door. Push the laundry into the drum completely to prevent the laundry from being caught in the door or CAUTION from falling out of the drum. 3. Add detergent and additives to the dispenser (see pages 26~27). 4. Select the appropriate cycle and options for the load (see pages 19~21). 5. Press the Start/Pause Button. The drum automatically rotates and measures the weight of the laundry without supplying water in order to adjust the wash time. (The rotating display on the display panel indicates that the weight of the laundry is being measured.) 6. The Wash Indicator light will illuminate. 7. The estimated cycle time will appear in the display. The time may fluctuate to indicate the time remaining in the cycle better. The actual time required for a cycle may differ from the estimated time in the display depending on the water pressure, water temperature, detergent, and laundry. 8. Before your washer starts to fill, it will make a series of clicking noises to check the door lock and do a quick drain. When the cycle is complete, the Door Lock light will go out and End will appear in the display. DO NOT attempt to open the door until the Door Lock light is off. To add a forgotten item, see the Loading your Washer section above. When your washer is restarted after a pause, expect a delay of up to 15 seconds before the cycle continues. Pressing the Power button cancels the cycle and stops your washer. The Wash, Rinse, and Spin indicator lights will illuminate during those portions of the cycle. Do not place anything on top of your washer while it is running. WARNING 18_English

19 washing a load of laundry Overview of the control panel WF42H5200A* WF42H5100A* 03 washing a load of laundry WF42H5000A* Cycle Selector Select the appropriate cycle for the type of load. This will determine the tumble pattern and spin speed for the cycle. To minimize wrinkling of laundry, select the Perm Press cycle. NORMAL - For most fabrics including cottons, linens, and normally soiled garments. HEAVY DUTY - For sturdy, colorfast fabrics and heavily soiled garments. SANITIZE - For heavily soiled, colorfast garments. This cycle heats the water to 150 F to eliminate bacteria. (Only for WF42H5200A*,WF42H5100A* models) If you select pause during the heating portion of the Sanitize Cycle, your Washer door will remain locked for your safety. When selecting this cycle, the water heats to an extra high temperature to remove 99.9% of certain bacteria typically found on clothing, bedding, or towels. This certification is conducted by NSF International, an independent third-party testing and certification organization. English _19

20 washing a load of laundry Please check the garment care label to avoid garment damage. Only sanitizing cycles have been designed to meet the requirements of this protocol for sanitization efficacy. NSF Protocol P172 Sanitization Performance of Residential and Commercial, Family-Sized Clothes Washers ALLERGEN - This course is applied to remove dust mites, pet dander or other allergic substances of the fabric. Only ALLERGEN cycle of WF42H5200* has been designed to meet the requirement of P351 for allergen reduction efficacy. NSF Protocol P351 Allergen Reduction Performance of Residential and Commercial,Family-Sized Clothes Washers Digital display Temperature selection button Spin selection button Soil Level selection button RINSE + SPIN - Use for loads that need rinsing only or to add rinse-added fabric softener to a load. BEDDING - For bulky items such as blankets, comforters and sheets. When you are washing bulky items, use liquid detergent. QUICK WASH - For lightly soiled garments needed quickly. PERM PRESS - For wash-and-wear, synthetic fabrics, and lightly to normally soiled garments. DELICATES - For sheer fabrics, bras, lingerie silk, and other handwash only fabrics. For best results, use liquid detergent. ACTIVE WEAR - Use this cycle to wash exercise wear such as sports jerseys, training pants, shirts/tops and other performance clothing. This cycle provides effective soil removal with gentle action for special fabric care. (Only for WF42H5100A*, WF42H5000A* models) The large Digital Display is easy to use. It provides instructions and diagnostics while keeping you updated on the cycle status and time remaining. Press the button repeatedly to cycle through the different water temperature options. Hot - Whites and heavily soiled, colorfast items. Warm - Colorfast items. When warm rinse is selected, only the final rinse will be warm. The other rinses will be cold to conserve energy. Eco Warm - Moderately soiled, colorfast items; most wrinkle-free items. Cold - Brightly colored, very lightly soiled items. Press the button repeatedly to cycle through the different spin speed options. (Rins hold (All Lamp Turn Off) No Spin Low Medium High ) To minimize wrinkling of wrinkle free and no iron fabrics, DO NOT use overload your Washer. High - Use for underwear, t-shirts, jeans and sturdy cottons. Medium - Use for jeans, wrinkle-free or wash-and-wear items and synthetics. Low - Use for delicate items needing a slow spin speed. No Spin - Drains your Washer without spinning. Use for extremely delicate items that cannot tolerate any spin. Rinse Hold (All Lamp Turn Off) - The laundry remains soaking in the final rinse water. Either a drain or spin cycle must be performed to unload the laundry. Press the button to select the soil level/washing time. (Light Normal Heavy) Heavy - For heavily soiled loads. Normal - For moderately soiled loads. This setting is best for most loads. Light - For lightly soiled loads. 20_English

21 6 7 8 Select Cycle Option Start/Pause selection button Power button Child Lock Press these buttons to select different cycle options. Extra Rinse - Add an additional rinse at the end of the cycle to remove laundry additives and perfumes more thoroughly. Extra Spin - Add additional time to remove more water from loads. Spin Only - The option to start only Spin of each course. Steam - Press this button to use the Steam Wash function. Steam Wash is available with the Normal, Heavy Duty, Bedding, Sanitize and Allergen cycles. For heavily soiled, colorfast garments, Steam Wash improves stain treatment and uses less water (See page 25). (Only for WF42H5200A* models.) Sound - When you activate the Sound off function, the Sound [ ] lamp illuminates. My Cycle - Choose your favorite cycle including temperature, spin, soil level, options, etc. (see page 22) Delay End - Any cycle can be delayed for up to 24 hours in one-hour increments. Displayed hour indicates the time at which the wash will be started. (See page 22). Self Clean+ - Use to clean dirt and possible mold from the drum. Regular use (after every 40 washes) is recommended. No detergent or bleach is needed (see page 31). Smart Care - This function enables you to check the status of the washing machine using a smartphone. Press to pause and restart programs. Press once to turn your washer on, press again to turn your washer off. If the washer is left on for more than 10 minutes without any buttons being touched, the power automatically turns off. Child Lock prevents children from playing with your washer. Once you have activated the Child Lock function, the control panel cannot be activated, preventing children from playing with the washer. Activating the Child Lock function Press and hold both the Soil Level and Spin buttons simultaneously for 3 seconds. When you activate the Child Lock function, the door locks and the Child Lock lamp illuminates. If you press the START/PAUSE button after you have activated the Child Lock function, none of the buttons will work except for the POWER button. If you press a button when the buttons are locked, the Child Lock lamp blinks. Pausing the Child Lock function When the door is locked or the buttons are locked by the Child Lock function, you can pause the Child Lock operation for 1 minute by pressing and holding both the Soil Level and Spin buttons simultaneously for approximately 3 seconds. If you pause the Child Lock mode temporarily, the door lock is released for 1 minute for user convenience. During this period, the Child Lock lamp blinks. If you open the door after the minute is over, an alarm sounds for up to 2 minutes. If you close the door within the 2 minutes, the door is locked and the Child Lock function is reactivated. If you close the door after the 2 minutes, the door is not locked automatically and no alarm sounds. 03 washing a load of laundry English _21

22 washing a load of laundry Deactivating the Child Lock function Press and hold both the Soil Level and Spin buttons simultaneously for approximately 6 seconds. When you deactivate the Child Lock function, the door is unlocked and the Child Lock is turned off. The Child Lock function prevents children or the infirm from accidently operating the washer and injuring themselves. If a child enters the washing machine, the child may become trapped and suffocate. Once you have activated the Child Lock function, it continues working even if the power is turned off. Opening the door by force can result in injury due to damage to the product. To add laundry after you have activated the Child Lock function, you must first pause or deactivate the Child Lock function. WARNING CAUTION If you want to open the door of the washing machine when the Child Lock function is activated: Pause or deactivate the Child Lock function. Turn the washing machine off and then on again. Garment+ You can add or take out laundry items even after the wash has started, as long as the light is on. Pushing the START/PAUSE button unlocks the door, unless the water is too hot or if there is too much water in your washer. If you are able to unlock the door and wish to continue the wash cycle, close the door, and then press the START/PAUSE button. Delay End You can set the washing machine to start your wash automatically at a later time, choosing a delay time. The hour displayed indicates the time at which the wash will be started. 1. Set your wash cycles. 2. Press the Delay End button repeatedly until the delay time is set. 3. Press the START/PAUSE button. The Delay End indicator will be lit, and the clock will begin counting down until it reaches the set time. 4. To cancel a Delay End function, press the POWER button and then turn the washing machine on again. My Cycle Lets you save a custom wash cycle (temperature, spin, soil level, etc.) and then recall and use it with one button convenience. To save a cycle and selected options as your My Cycle, follow these steps: 1. Select the cycle using the Cycle Selector dial. 2. After cycle selection, set each option. See page 39 for available option settings with each cycle. 3. You can then store the selected cycle and options by pressing and holding the My Cycle button for longer than 3 seconds. The cycle and options you select will be displayed the next time you choose the My Cycle function. 4. Press the My Cycle button to load and use the saved My Cycle options. The My Cycle light will indicate activation. Also, the chosen course and option lights will flicker You can change the My Cycle settings by repeating the process above. The washer displays the last settings used the next time you choose My Cycle. If you press My Cycle and release it within 3 seconds, the previously saved cycles and options appear. If you press and hold My Cycle for 3 second or longer, the currently set cycles and options are saved and the LED blinks for 3 seconds. 22_English

23 Sound The Sound Off function can be selected during all courses. Smart Care This function enables you to check the status of the washing machine using a smartphone. 1. To enable the Smart Care function 1) WF42H5200A* press and hold the Sound button for 3 seconds within 10 seconds after turning the power on by pressing the Power button. 2) WF42H5100A* and WF42H5000A* model Press Smart Care button to use. WF42H5200A* WF42H5100A* WF42H5000A* 2. If the Smart Care function is activated, the LED on the window display rotates for 2 or 3 seconds and then the Smart Care indicator is lit on the display. 3. Run the Smart Care app on your smart phone. 4. The Smart Care function is optimized with Galaxy and iphone Series. 5. Focus your smart phone s camera on the display panel of the washing machine. 6. If the smart phone s camera is focused on the display panel of the washing machine, the panel and error message is automatically recognized and the error type and countermeasures are displayed on the smart phone. 7. If the smartphone fails to recognize the error code more than twice, please enter the error code displayed on the display panel of the washer manually into the Smart Care app. Downloading the Smart Care app Download the Samsung Laundry App into your mobile phone from the Android market or Apple App store. (Search word : Samsung Smart Washer/Dryer) Precautions when using Smart Care If a lighting device (e.g. fluorescent or lamp) is reflected on the display panel of the washing machine, the result on the display panel may not be recognized easily. If an error occurs more than twice, please manually enter the error code displayed on the display panel of the washing machine into the Smart Care app. If the angle of the smartphone camera and the display panel of the washing machine is incorrect, the error may not be recognized properly. Please try to hold the smart phone at an angle to the display panel as shown by the figure. 03 washing a load of laundry English _23

24 washing a load of laundry Washing clothes using the cycle selector Your new washing machine makes washing clothes easy, using Samsung s Fuzzy Control automatic control system. When you select a wash program, the machine will set the correct temperature, washing time, and washing speed. 1. Turn on your sink s water tap. 2. Press the Power button. 3. Open the door. 4. Load the articles of clothing one at a time loosely into the drum, without overfilling it. 5. Close the door. 6. Add detergent, softener, and pre-wash detergent (if necessary) into the appropriate compartments. 7. Use the Cycle Selector to select the appropriate cycle according to the type of material: NORMAL, HEAVY DUTY, BEDDING, SANITIZE,ALLERGEN(Only for WF42H5200A* model), RINSE+SPIN,QUICK WASH, PERM PRESS, DELICATES, ACTIVE WEAR(Only for WF42H5100A*, WF42H5000A* models). The relevant indicators will illuminate on the control panel. 8. At this time, you can control the wash temperature, the number of rinse cycles, the spinning speed, and the delay time by pressing the appropriate option button. 9. Press the Start/Pause button on the Cycle Selector and the wash will begin. The process indicator will light up and the remaining time for the cycle will appear in the display. Pause Option 1. Within 5 minutes of starting a wash, it is possible to add/remove laundry items to/from the wash. 2. Press the Start/Pause button to unlock the door. 3. The door cannot be opened when the water is too HOT or the water level is too HIGH. 4. After closing the door, press the Start/Pause button to restart the wash. When the cycle is finished: After the total cycle has finished, the power will turn off automatically. 1. Open the door. 2. Remove laundry. 24_English

25 Using steam wash If you select steam, the steam acts at the most effective times for the detected amount of laundry, maximizing the effect of the steam, increasing the wash temperature, enhancing the Soak effect, and improving wash performance. (Only for WF42H5200A* models) 1. Load the washer. 2. Press the Power button. 3. Turn the Cycle Selector and select a Steam Cycle. (The Deep Steam course automatically selects Steam.) 4. Press the Steam button. 5. Add detergent to the dispenser tray and add fabric softener up to the marked line. 6. Press the Start/Pause button. : The washer automatically selects the optimal wash conditions by sensing the weight of the laundry. Steam may not necessarily be visible during the steam cycles. Steam may not be present during the entire steam wash cycle. 03 washing a load of laundry ATC (Auto Temperature Control) ATC is the control function that the washer controls water temperature with temperature sensor (thermistor). Because there are numerous water temperatures depending on the customer s environments ( cold areas, warm areas, various water temperature, settings of heater temperature, etcs), ATC function in our washer maintains the certain level of wash temperature to output the best washing performance at each cycle. If you select normal & heavy duty cycles, those cycles are the regulation and UL course. Since new washers must reduce the amount of energy usage at first priority, customers will notice more cold water entering the washer. But This is Normal, not a problem. In those regulation cycles, Hot temperature is similar to acceptable adult bath-water temperature and warm temperature is similar to comfortable swimming-pool water temperature. If customers want to wash clothes in specific water temperature, customers should choose a different cycles at each temperature ( Hot/Warm/Eco Warm ) English _25

26 washing a load of laundry Detergent use Your Washer is designed to use high efficiency (HE) detergents. For best cleaning results, use a high efficiency detergents such as Tide HE, Wisk HE, Cheer HE, or Gain HE*. High efficiency detergents contain suds suppressors that reduce or eliminate suds. When fewer suds are produced, the load tumbles more efficiently and cleaning is maximized. WARNING Regular detergent is NOT recommended. Please use HE detergents only. Reducing the amount of detergent may reduce the quality of cleaning. It is important to pre treat stains, sort carefully by color and soil level, and avoid overloading. * Brand names are trademarks of their respective manufacturers. Features Automatic dispenser Your washer has separate compartments for dispensing detergent and color-safe bleach, chlorine bleach, and fabric softener. Add all laundry additives to their respective compartments before starting your washer. The automatic dispenser MUST ALWAYS be in place before you start your washer. DO NOT open the automatic dispenser when your washer is running. Usage Pointers: Never exceed the manufacturer s recommendations when adding detergent. This compartment holds liquid detergent for the main wash cycle, which the washer adds to the load at the beginning of the cycle. Before using powdered detergent, remove the Liquid Detergent holder from the compartment. Powdered detergent will not dispense from the Liquid Detergent holder. Liquid Detergent Pre wash compartment Detergent compartment Pour the recommended amount of laundry detergent directly into the detergent compartment before starting your washer. 26_English

27 Bleach compartment (Liquid chlorine bleach only) 1. Add chlorine bleach to the bleach compartment. DO NOT exceed the MAX FILL line. 2. Avoid splashing or over filling the compartment. 3. Your washer automatically dispenses bleach into the tub at the appropriate time. 4. The dispenser automatically dilutes liquid chlorine bleach before it reaches the wash load. Never pour undiluted liquid chlorine bleach directly onto the load or into the tub. It is a powerful chemical and can cause fabric damage, such as weakening of the fibers or color loss, if not used properly. Oxi-type boosters or color-safe bleach can be added to the drum prior to adding laundry. Put the laundry into the drum only after confirming that the oxi-type boosters or color-safe bleach has completely entered the hole of the drum. To use powdered detergent and powder oxi-type boosters or powdered color-safe bleach at the same time, it is more effective to put them in the drum together before adding the laundry. When you use powdered detergent, remember to remove the Liquid Detergent holder from the detergent compartment. Fabric Softener compartment Bleach compartment 03 washing a load of laundry Fabric softener compartment 1. Pour the recommended amount of liquid fabric softener into the softener compartment. For smaller loads, use less than one capful. 2. Dilute the fabric softener with water until it reaches MAX FILL in the compartment. 3. The dispenser automatically releases liquid fabric softener at the proper time during the rinse cycle. Use the softener compartment ONLY for liquid fabric softeners. DO NOT use a Downy Ball* in the Fabric softener compartment of this washer. It will not be added at the appropriate time. Use the detergent compartment. * Brand names are trademarks of their respective manufacturers. If you overfill the detergent, bleach, or softener compartments, the contents of the compartment will automatically be released into the washer. This could damage any garments that are in the drum. English _27