DODGE DAKOTA (08+) with Cargo Rails Option

DODGE DAKOTA (08+) with Cargo Rails Option 6.5' Bed - Order 82211088 & 82211089 5.25' Bed - Order 82211087 "ONLY" For Service Replacement Parts and Technical Support call" 1-800-322-0522 GB E F INSTALLATION INSTRUCTION INSTRUCCIONES DE MONTAJE NOTICE DE MONTAGE FOLD-A-COVER HARD FOLDING TONNEAU COVER CUBIERTA DURA PLEGABLE FOLD-A-COVER PARA LA CAPOTA POSTERIOR COUVERCLE DE PLATEAU RIGIDE À SECTIONS REPLIABLES "FOLD-A-COVER " Subject to alteration without notice Reservadas modificaciones técnicas Sous réserve de modifications techniques Expert Fitment Required Montaje sólo por el concesionario Montage par spécialiste nécessaire 08-08-2007 K6860304 1 of 13

GB APPLICATION: DODGE DAKOTA (08+) The Fold a Cover kit is required for use with this hardware kit. Temperature should be no lower than 70 F (21.1 C) when installing. Be sure the truck is setting on a level surface. Apply a dab of lock tight to each fastener before use. Record the key number and place in glove box or write it in your owner s manual. Refer to the Operation and Care Label located on the underside of the rearmost panel on cover (driver s side). Product should NOT be installed if vehicle is equipped with overrail bedliner. On trucks equipped with underrail bedliner and tailgate cover. To improve fit of the product it may be necessary to lower tailgate and to remove front bulbseal. E APLICACIÓN: DODGE DAKOTA (08+) Se requiere el juego Fold a Cover para utilizar este juego de piezas. La temperatura no debe ser inferior a los 21.1 C (70 F) durante la instalación. Asegúrese de que la camioneta esté en una superficie plana y horizontal. Aplique una pizca de sellador de rosca a cada fijador antes de ponerlo en uso. Registre el número de la llave y colóquelo en la guantera o escríbalo en su Manual del propietario. Consulte el rótulo de Operación y cuidados ubicado en el lado de abajo del panel extremo posterior de la cubierta (del lado del conductor). Este producto no debe ser instalado si el vehículo está equipado con una camisa de caja del tipo que cubre los largueros. En camiones equipados con una camisa de caja colocada bajo los largueros y una cubierta de la compuerta trasera. Para mejorar el encaje del producto, puede ser necesariobajar la compuerta trasera y retirar el sello del foco. F APPLICATION : DODGE DAKOTA (08+) L'ensemble " Fold-a-cover " doit être utilisé avec cette trousse de matériel. Lors de l'installation, la température ne doit pas être inférieure à 21.1 C (70 F). Assurez-vous que votre camion se trouve sur une surface plane. Enduisez chaque élément de fixation de colle frein avant l'utilisation. Notez le numéro de code et laissez-le dans la boîte à gants ou inscrivez-le dans votre manuel du propriétaire. Consultez l'étiquette Fonctionnement et entretien (Operation and Care) située sur la face antérieure du panneau arrière, sur le couvercle (côté conducteur). Le produit ne doit pas être installé si le véhicule est équipé d'une doublure de caisse montée sur le longeron. Sur les véhicules équipés d'une doublure de caisse montée sous le longeron et d'un capot de hayon, il peut être nécessaire d'abaisser le hayon et de retirer l'étanchéité d'ampoule. 3/16 4.7mm 5/16, 7/16 5/64 5/32 5/32 2 of 13

A B C 8x 3.0 (76,2mm) 2.5 (63,5mm) D 4x E 2x F 4x G 8x 1/4 (6,4mm) black 1/4 (6,4mm) black H 8x J 8x K 8x L M 2x N 4x 1/4 (6,4mm) silver P 2x Q 8x R 8x S 2x T?---For Service Replacement Parts and Technical Support call 1-800-322-0522---? 2x U 4x V W X 3 of 13

W Without Bedliner With Bedliner 1 long each 1/2 long each 2.0 MAX 1 Cut 2 from seal W, then cut into (2) smaller pieces as shown (size depending on whether vehicle is equipped with bedliner) W1 W2 W1 Clean painted vehicle surface adjacent to bed rail cap and wipe with isopropyl alcohol. Remove protective film from seal and press into place as shown. W/O BEDLINER SIN CAMISA DE CAJA SANS DOUBLURE W1 W2 2X Bedliner 2 WITH BEDLINER CON CAMISA DE CAJA AVEC DOUBLURE 4 of 13

5/32 REMOVE & RE-USE DO NOT FULLY TIGHTEN NO CEÑIR COMPLETAMENTE NE SERREZ PAS LES VIS TOTALEMENT D A 4X K H 4X J 4X C 4X D E 2X F 5/16 G 4X DO NOT FULLY TIGHTEN NO CEÑIR COMPLETAMENTE NE SERREZ PAS LES VIS TOTALEMENT 3 Repeat for other side using item B instead of item A C/L Optional tie-down location relative to item E (front location shown above) 3 11/16 94mm C/L 4 1/2 114mm E Measurements are from front or rear end of cargo rail extrusion to center of catch pocket. 4 5 of 13

5 CENTER THE COVER AND SIDE RAILS EVENLY ONTO THE TRUCK BOX. Z Z A 5/8" (16mm) VIEW -A- Flush PROPER FIT ENCAJE CORRECTO INSTALLATION CORRECTE 1/8" (3mm) 6 6 of 13

1/2 12.5mm 1/2 12.5mm Side View 7 8 3/16 (4.7mm) L 9 10 L M 2X 11 12 POSITION COVER AND SIDE RAILS SO THE LATCH ENGAGES THE LOOP. COLOQUE LA CUBIERTA Y LOS LARGUEROS LATERALES DE MANERA QUE EL PESTILLO ENCAJE EN EL ANILLO. PLACEZ LE COUVERCLE ET LES LONGERONS DE MANIÈRE À CE QUE LE VERROU S'ENCLENCHE DANS LA BOUCLE. 7 of 13

15 P LOCK TITE Apply Loctite to bolt threads. N 2X 25 in.-lbs. (2.8 N m) 5/32 13 S LOCK TITE T 2X 70 in.-lbs. (7.9 N m) Q R 2X 16 2X R 7/16 7/16 Q 2X 70 in.-lbs. (7.9 N m) 14 15 5/32 LOCK TITE H 70 in.-lbs. (7.9 N m) 1/32 (1mm) TYP REPEAT 14-16 FOR OTHER SIDE. REPITA LOS PASOS 14 A 16 EN EL OTRO LADO. RÉPÉTEZ LES ÉTAPES 14 À 16 POUR L'AUTRE CÔTÉ. 16 8 of 13

U 4X 5/64 17 End View 19 5/16 2X 25 in.-lbs. (2.8 N m) G LOCK TITE End View REPEAT FOR OTHER LOCATIONS Lower tailgate then close rear panel to adjust latch engagement front-to-rear and up/down 18 19 Press down on panel so that latch engages easily into catch bracket while maintaining minimal clearance 9 of 13

5/32 70 in.-lbs. (7.9 N m) H 20 REPEAT FOR OTHER SIDE. REPITA EN EL OTRO LADO. RÉPÉTEZ POUR L'AUTRE CÔTÉ. DO NOT ATTACH SEALS CUT TO LENGTH ONLY V W 21 Flush - both ends Locate between end caps Do not remove seal liner covering adhesive. Place each seal on cover as shown, mark length, then trim. 10 of 13

V Cut at tape edge After cutting seal to length, trim both ends as shown W/O BEDLINER SIN CAMISA DE CAJA SANS DOUBLURE 3/16" (5mm) WITH BEDLINER CON CAMISA DE CAJA AVEC DOUBLURE V 22 3/4" (19mm) 3/4" (19mm) CRITICAL PLACEMENT OF SEAL V Refer to Views A & B W V X Allow to dry before applying seals. Side View Truck not shown WITH BEDLINER CON CAMISA DE CAJA AVEC DOUBLURE Side View SEE STEP 23 A & B Tape edge aligned with edge of radius Side View Truck not shown View A W/O BEDLINER SIN CAMISA DE CAJA SANS DOUBLURE View A SEE STEP 23 A & B Seal edge aligned with channel edge 23 View B View B 11 of 13

FRONT SEAL FIT W/O BEDLINER SIN CAMISA DE CAJA SANS DOUBLURE Front Panel WITH BEDLINER CON CAMISA DE CAJA AVEC DOUBLURE Front Seal Front Seal Bedliner 23A RECOMMENDED SEAL WET-OUT PROCEDURE Starting at one end and using an end wrench or similar tool, apply approx. 10lb (44.5N) of downward force above the tape where indicated and slide the wrench to the other side while maintaining even pressure. 23B 12 of 13

NO TONNEAU IS 100% WATERPROOF - This tonneau has been rigorously tested under various types of car wash systems with minimal water entry. To minimize moisture from entering bed area, apply silocone clear type sealer (Mopar part # 04467708) into area shown. Passenger side shown, apply to drivers side also. 24 13 of 13