Operating Instructions Manuel d instructions Manual de Instrucciones

Transcription

1 WM MP3 CD Player/Receiver Récepteur/lecteur CD avec lecture WM/MP3 Reproductor de CD, WM y MP3/receptor Model: (CQ-C5403U) Operating Instructions Manuel d instructions Manual de Instrucciones TEXT Please read these instructions (including Limited Warranty and Customer ervices Directory ) carefully before using this product and keep this manual for future reference. Prière de lire attentivement ces instructions (y compris la «Garantie limitée» et le «Répertoire des services à la clientèle») avant d utiliser ce produit et conserver ce mode d emploi pour s y référer ultérieurement. Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro.

2 E G LI H 1 afety Information Read the operating instructions for the unit and all other components of your car audio system carefully before using the system. They contain instructions about ho to use the system in a safe and effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this manual. This manual uses pictographs to sho you ho to use the product safely and to alert you to potential dangers resulting from improper connections and operations. The meanings of the pictographs are explained belo. It is important that you fully understand the meanings of the pictographs in order to use this manual and the system properly. Warning This pictograph intends to alert you to the presence of important operating instructions and installation instructions. Failure to heed the instructions may result in severe injury or death. Caution This pictograph intends to alert you to the presence of important operating instructions and installation instructions. Failure to heed the instructions may result in injury or material damage. Warning Observe the folloing arnings hen using this unit. The driver should neither atch the display nor operate the system hile driving. Watching the display or operating the system ill distract the driver from looking ahead of the vehicle and can cause accidents. lays stop the vehicle in a safe location and use the parking brake before atching the display or operating the system. Use the proper poer supply. This product is designed for operation ith a negative grounded 12 V DC battery system. ever operate this product ith other battery systems, especially a 24 V DC battery system. Keep batteries and insulation film out of reach of infants. Batteries and insulation film can be ingested, so keep them out of the reach of infants. If an infant ingests a battery or insulation film, please seek immediate medical attention. Protect the Deck Mechanism. Do not insert any foreign objects into the slot of this unit. Do not disassemble or modify the unit. Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your dealer or an authorized Panasonic ervicenter. Do not use the unit hen it is out of order. If the unit is out of order (no poer, no sound) or in an abnormal state (has foreign objects in it, is exposed to ater, is smoking, or smells), turn it off immediately and consult your dealer. The remote control unit should not lie about in the car. If the remote control unit lies about, it could fall on the floor hile driving, get edged under the brake pedal, and lead to a traffic accident. Refer fuse replacement to ualified service personnel. When the fuse blos out, eliminate the cause and have it replaced ith the fuse prescribed for this unit by a ualified service engineer. Incorrect replacement of the fuse may lead to smoke, fire, and damage to the product. Observe the folloing arnings hen installing. Disconnect the lead from the negative ( ) battery terminal before installation. Wiring and installation ith the negative ( ) battery terminal connected may cause electrical shock and injury due to a short circuit. ome cars euipped ith the electrical safety system have specific procedures of battery terminal disconnection. FILURE TO FOLLOW THE PROCEDURE MY LED TO THE UITEDED CTIVTIO OF THE ELECTRICL FETY YTEM REULTIG I DMGE TO THE VEHICLE D PEROL IJURY OR DETH. ever use safety-related components for installation, grounding, and other such functions. Do not use safety-related vehicle components (fuel tank, brake, suspension, steering heel, pedals, airbag, etc.) for iring or fixing the product or its accessories. Installing the product on the air bag cover or in a location here it interferes ith airbag operation is prohibited. Check for piping, gasoline tank, electric iring, and other items before installing the product. If you need to open a hole in the vehicle chassis to attach or ire the product, first check here the ire harness, gasoline tank, and electric iring are located. Then open the hole from outside if possible. ever install the product in a location here it interferes ith your field of vision. ever have the poer cord branched to supply other euipment ith poer. fter installation and iring, you should check the normal operation of other electrical euipment. The continuation of their using in abnormal conditions may cause fire, electrical shock or a traffic accident. In the case of installation to an airbag-euipping car, confirm arnings and cautions of the vehicle manufacturer before installation. Make sure the leads do not interfere ith driving or getting in and out of the vehicle. Insulate all exposed ires to prevent short circuiting. 2

3 E G LI Caution Observe the folloing cautions hen using this unit. Keep the sound volume at an appropriate level. Keep the volume level lo enough to be aare of road and traffic conditions hile driving. Do not insert or allo your hand or fingers to be caught in the unit. To prevent injury, do not get your hand or fingers caught in moving parts or in the disc slot. Especially atch out for infants. This unit is designed for use exclusively in automobiles. Do not operate the unit for a prolonged period ith the engine turned off. Operating the audio system for a long period of time ith the engine turned off ill drain the battery. Do not expose the unit to direct sunlight or excessive heat. Otherise these ill raise the interior temperature of the unit, and it may lead to smoke, fire, or other damage to the unit. Do not use the product here it is exposed to ater, moisture, or dust. Exposure of the unit to ater, moisture, or dust may lead to smoke, fire, or other damage to the unit. Make especially sure that the unit does not get et in car ashes or on rainy days. Observe the folloing cautions hen installing. Refer iring and installation to ualified service personnel. Installation of this unit reuires special skills and experience. For maximum safety, have it installed by your dealer. Panasonic is not liable for any problems resulting from your on installation of the unit. Follo the instructions to install and ire the product. ot folloing the instructions to properly install and ire the product could cause an accident or fire. Take care not to damage the leads. When iring, take care not to damage the leads. Prevent them from getting caught in the vehicle chassis, scres, and moving parts such as seat rails. Do not scratch, pull, bend or tist the leads. Do not run them near heat sources or place heavy objects on them. If leads must be run over sharp metal edges, protect the leads by inding them ith vinyl tape or similar protection. Use the designated parts and tools for installation. Use the supplied or designated parts and appropriate tools to install the product. The use of parts other than those supplied or designated may result in internal damage to the unit. Faulty installation may lead to an accident, a malfunction or fire. Do not block the air vent or the cooling plate of the unit. Blocking these parts ill cause the interior of the unit to overheat and ill result in fire or other damage. Do not install the product here it is exposed to strong vibrations or is unstable. void slanted or strongly curved surfaces for installation. If the installation is not stable, the unit may fall don hile driving and this can lead to an accident or injury. Installation ngle The product should be installed in a horizontal position ith the front end up at a convenient angle, but not more than 30. The user should bear in mind that in some areas there may be restrictions on ho and here this unit can be installed. Consult your dealer for further details. Wear gloves for safety. Make sure that iring is completed before installation. To prevent damage to the unit, do not connect the poer connector until the hole iring is completed. Do not connect more than one speaker to one set of speaker leads. (except for connecting to a teeter) Observe the folloing cautions hen handling the battery for the remote control unit. Use only specified battery (CR2025). Match the polarity of the battery ith the (+) and ( ) marks in the battery case. Replace dead battery as soon as possible. Remove the battery from the remote control unit hen not using it for an extended period of time. Insulate the battery (by placing them in a plastic bag or covering them ith vinyl tape) before disposal or storage. Dispose of the battery according to the local regulations. Do not disassemble, recharge, heat or short the battery. Do not thro a battery into a fire or ater. In case of battery leakage Thoroughly ipe the battery liuid off the battery case and insert ne battery. If any part of your body or clothing comes into contact ith battery liuid, ash it ith plenty of ater. If battery liuid comes into contact ith your eyes, ash them ith plenty of ater and get immediate medical attention. H 2 3

4 E G LI afety Information (continued) H 3 Caution THI PRODUCT I CL I LER PRODUCT. UE OF COTROL OR DJUTMET OR PERFORMCE OF PROCEDURE OTHER TH THOE PECIFIED HEREI MY REULT I HZRDOU RDITIO EXPOURE. DO OT OPE COVER D DO OT REPIR BY YOURELF. REFER ERVICIG TO QULIFIED PEROEL. The folloing applies only in the U... Part 15 of the FCC Rules FCC Warning: ny unauthorized changes or modifications to this euipment ould void the user's authority to operate this device. 4

5 Before Reading These Instructions Panasonic elcomes you to our constantly groing family of electronic products oners. We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured ith carefully selected components, and assembled by people ho are proud of the reputation their ork has built for our company. We kno this product ill bring you many hours of enjoyment, and after you discover the uality, value and reliability e have built into it, you too ill be proud to be a member of our family. E G LI H 4 Differences beteen 2 Models This operating instruction manual is for 2 models CQ-C5403U and CQ-C5303U. ll illustrations throughout this manual represent model CQ-C5403U unless otherise specified. The folloing table describes the differences beteen 2 models. Models Features Pre-amp output voltage/impedance uboofer output voltage/impedance CQ-C5403U 4 V/60 Ω 4 V/60 Ω CQ-C5303U 2.5 V/200 Ω 2.5 V/200 Ω Customer ervices Directory U... Obtain Product Information and Operating ssistance; locate your nearest Dealer or ervicenter; purchase Parts and ccessories; or make Customer ervice and Literature reuests by visiting our Web ite at: or, contact us via the eb at: You may also contact us directly at: P (7262), Monday-Friday 9 am-9 pm; aturday-unday 10 am-7 pm, ET. For hearing or speech impaired TTY users, TTY : ccessory Purchases: Purchase Parts, ccessories and Instruction Books online for all Panasonic Products by visiting our Web ite at: or, send your reuest by to: npcparts@panasonic.com You may also contact us directly at: (Phone) (Fax Only) (Monday- Friday 9 am to 8 pm, ET.) Panasonic ervices Company th venue outh, Kent, W (We accept Visa, MasterCard, Discover Card, merican Express, and Personal Checks) For hearing or speech impaired TTY users, TTY : ervice in Puerto Rico Panasonic Puerto Rico, Inc. Panasonic ales Company Factory ervicenter: ve. 65 de Infantería, Km. 9.5, an Gabriel Industrial Park, Carolina, Puerto Rico Phone (787) , Fax (787) CD WRRTY ERVICE FOR PRODUCT OPERTIO ITCE, please contact: Our Customer Care Centre: Telephone #: (905) #: Fax #: (905) link: Contact Us on.panasonic.ca FOR PRODUCT REPIR, please locate your nearest uthorized ervicentre at.panasonic.ca: Link : ervicentres TM locator under Customer support Panasonic Factory ervice: Vancouver Toronto Panasonic Canada Inc. Panasonic Canada Inc Riverside Way 5770 mbler Drive Richmond, BC V6W 1K8 Mississauga, O L4W 2T3 Tel: (604) Tel: (905) Fax: (604) Fax: (905) IF YOU HIP THE PRODUCT TO ERVICETRE Carefully pack and send prepaid, adeuately insured and preferably in the original carton. Include details of the defect claimed, and proof of date of original purchase. 5

6 E G LI H 5 Limited Warranty U... POIC COUMER ELECTROIC COMPY, DIVIIO OF POIC CORPORTIO OF ORTH MERIC One Panasonic Way, ecaucus, e Jersey POIC LE COMPY, DIVIIO OF POIC PUERTO RICO, IC. ve. 65 de infanteria, Km. 9.5, an Gabriel Industrial Park Carolina, Puerto Rico POIC UTO PRODUCT LIMITED WRRTY LIMITED WRRTY COVERGE If your product does not ork properly because of defects in materials and orkmanship. Panasonic Consumer Electronics Company or Panasonic ales Company (collectively referred to as the arrantor ) ill, for the length of the period indicated in the chart belo, hich starts ith the date of original purchase ( arranty period ), at its option either (a) repair your product ith ne or refurbished parts, or (b) replace it ith a ne or refurbished product. The decision to repair or replace ill be made by the arrantor. Categories Parts Labor udio Components (except items listed belo) One (1) Year One (1) Year MXE eries udio Components (except items To (2) Years To (2) Years listed belo) peakers One (1) Year ot pplicable ccessories (in exchange for defective items) inety (90) Days ot pplicable During the Labor arranty period, there ill be no charge for labor. During the Parts arranty period, there ill be no charge for parts. You must carry in or mail in your product during the arranty period. If non-rechargeable batteries are included, they are not arranted. This arranty only applies to products purchased and serviced in the United tates or Puerto Rico. This arranty is extended only to the original purchaser of a ne product hich as not sold as is. purchase receipt or other proof of the original purchase date is reuired for arranty service. CRRY-I OR MIL-I ERVICE For Carry-In or Mail-In ervice in the United tates, call P (7262) or visit Panasonic Web ite: For assistance in Puerto Rico, call Panasonic ales Company (787) or fax (787) LIMITED WRRTY LIMIT D EXCLUIO This arranty OLY COVER failures due to defects in materials and orkmanship, and DOE OT COVER normal ear and tear or cosmetic damage. The arranty LO DOE OT COVER damages hich occurred during shipment, failures hich are caused by products not supplied by the arrantor, failures hich result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustment, maladjustment of consumer control, improper maintenance, improper antenna, inadeuate signal reception or pickup, poer line surge, improper voltage supply, lightning, modification, commercial use (such as use in hotels, offices, restaurants, or other business uses) or rental use of the product, or service by anyone other than the technician from Factory ervicenter or other authorized service centers, or damage that is attributable to acts of God. THERE RE O EXPRE WRRTIE EXCEPT LITED UDER LIMIT- ED WRRTY COVERGE. THE WRRTOR I OT LIBLE FOR ICI- DETL OR COEQUETIL DMGE REULTIG FROM THE UE OF THI PRODUCT, OR RIIG OUT OF Y BRECH OF THI WRRTY. (s examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, travel to and from the servicer, and loss of media, data or other memory contents. The items listed are not exclusive, but are for illustration only.) LL EXPRE D IMPLIED WR- RTIE, ICLUDIG THE WRRTY OF MERCHTBILITY, RE LIMIT- ED TO THE PERIOD OF THE LIMITED WRRTY. ome states do not allo the exclusion or limitation of incidental or conseuential damages, or limitations on ho long an implied arranty lasts, so the exclusions may not apply to you. This arranty gives you specific legal rights and you may also have other rights hich vary from state to state. If a problem ith this product develops during or after the arranty period, you may contact your dealer or ervicenter. If the problem is not handled to your satisfaction, then rite to arrantor s Consumer ffairs Department at the addresses of the arrantor. PRT D ERVICE WHICH RE OT COVERED BY THI LIMITED WR- RTY RE YOUR REPOIBILITY. Customer s Record Model o. erial o. Dealer s o. Code o. Dealer s ddress Date of Purchase CD Panasonic Canada Inc mbler Drive, Mississauga Ontario L4W 2T3 POIC PRODUCT LIMITED WRRTY Panasonic Canada Inc. arrants this product to be free from defects in materials and orkmanship and agrees to remedy any such defect for a period as stated belo from the date of original purchase. CR UDIO PRODUCT OE (1) YER, PRT D LBOUR (The labour to install or remove the product is not arranted) LIMITTIO D EXCLUIO This arranty does not apply to products purchased outside Canada or to any product hich has been improperly installed, subjected to usage for hich the product as not designed, misused or abused, damaged during shipping, or hich has been altered or repaired in any ay that affects the reliability or detracts from the performance, nor does it cover any product hich is used commercially. Dry cell batteries are also excluded from coverage under this arranty. This arranty is extended to the original end user purchaser only. purchase receipt or other proof of the original purchase date is reuired before arranty service is performed. THI EXPRE, LIMITED WRRTY I I LIEU OF LL OTHER WR- RTIE, EXPRE OR IMPLIED, ICLUDIG Y IMPLIED WRRTIE OF MERCHTBILITY D FITE FOR PRTICULR PURPOE. I O EVET WILL POIC CD IC. BE LIBLE FOR Y PECIL, IDIRECT OR COEQUETIL DMGE. In certain instances, some jurisdictions do not allo the exclusion or limitation of incidental or conseuential damages, or the exclusion of implied arranties, so the above limitations and exclusions may not be applicable. 6

7 Features Contents E G LI Wide array of components for system upgrade Various optional components allo users to obtain availability of ide range of system upgrade. Upgrading the system delivers relaxed V space in a car. For further information, refer to the separate ystem Upgrade Guidebook. CD changer The optional adapter (Conversion Cable for DVD/CD Changer: C-CC30U) allos you to connect the optional Panasonic CD changer unit (CX-DP880). ipod The optional adapter (Direct Cable for ipod: C- DC300U) allos you to connect the optional ipod series. XM atellite Radio You can connect the optional XM receiver (XMD1000) ith optional Digital dapter. For details, refer to the operating instructions for the XM receiver. irius atellite Radio You can connect the optional irius atellite radio receiver (IR-P1). Hands Free Phone ystem You can connect the optional Bluetooth hands-free kit (CY-BT100U). ote: CY-BT100U is designed only for receiving calls. It cannot send calls. You can connect the optional Expansion Module (hub unit) (CY-EM100U). Connection of the Expansion Module allos you to simultaneously connect optional devices mentioned before as ell as other V devices. For details, refer to the operating instructions for the Expansion Module. Fully Motorized Face Plate touch is all it takes to slide the face plate don for access to the disc slot. three-stage tilt function permits vieing angle to be adjusted to 15, 25 or 35 degrees for optimum display visibility. Q (ound Quality) You have 6 preset modes (FLT, ROCK, POP, VOCL, JZZ, CLUB). You can customize your setting for these (except FLT) and save them for instant recall. Q3 (3-Band ound Quality) Center freuency and level are adjustable in each of 3 bands. This lets you fine-tune sound uality for each genre to suit car-interior acoustics and your personal preferences. (a Page 22) Common afety Information... 2 Before Reading These Instructions...5 Customer ervices Directory...5 Limited Warranty...6 Features... 7 Contents... 7 ccessories... 8 Remote Control Unit... 8 Preparation... 9 Remote Control Unit Main Unit Cancellation of Demonstration Clock etting General Each source Radio Before Disc Playback CD Player MP3/WM Player otes on MP3/WM s needed udio ettings Volume Bass/Treble Q djustment Balance/Fader uboofer Level uboofer LPF (Lo Pass Filter) Function ettings Demonstration Dimmer (display brightness setting) pectrum nalyzer Display Patterns (PTTER) Mute/ttenuation UX kip ecurity Function nti-theft ystem Fuse Maintenance otes on Discs Troubleshooting pecifications ote: Refer to the ystem Upgrade Guidebook for operation of optional devices such as a CD changer and ipod. H 6 7

8 XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXX XXXXXXXXXXXXXXXX POWER OURCE MEU RC EL ET VOL BD MUTE RDOM C REPET TUE TUE # 0 DIP UMBER CR UDIO E G LI ccessories H 7 OO-OOOOO OO-OOOOO Operating Instructions (YEFM285752) ystem Upgrade Guidebook (YEFM262692) Instruction kit Q'ty: 1 set Installation Instructions (YEFM294105) Oners Information Card Removable Face Plate Case (YEF131839) Q'ty: 1 Remote Control Unit (Includes a battery) (EUR ) Q'ty: 1 Trim Plate (YEFC051014) Q'ty: 1 Poer Connector (YGJ021012) Q'ty: 1 Mounting Collar (YEFX ) Q'ty: 1 Lock Cancel Plate Q'ty: 2 Mounting Bolt Q'ty: 1 Installation kit (YEP0FZ5698) Rubber Bushing Q'ty: 1 ote: The number in parentheses underneath each accessory part name is the part number for maintenance and service. ccessories and their parts numbers are subject to modification ithout prior notice due to improvements. Trim Plate and Mounting Collar are mounted on the main unit at shipment. Remote Control Unit This instruction manual explains operations for use ith the buttons on the main unit. (Different operations excluded) Poer ource et Band Pause Random can Repeat Track/folder/file/disc number input Folder/disc selection Function setting POWER OURCE RC ET BD 1 RDOM 4 7 TUE # UMBER MEU EL MUTE 2 3 C REPET CR UDIO VOL 9 TUE DIP Menu elect Volume/audio setting Mute/attenuation [0] to [9] Tune Track/file selection Fast forard/fast reverse Display 8

9 Preparation Preparation Before Initial Use Pull the insulation film out from the backside of remote control gently. Battery Replacement Remove the battery holder ith the remote control unit placed on a flat surface. tick your thumbnail into the groove, and push the holder in the direction of the arro, and at the same time. Pull it out in the direction of the arro using a tough pointed object. Put a battery in the case ith (+) side facing up. eput the case back. Remote Control Unit Tough pointed object Back side 3 2 Warning Keep a battery aay from children to avoid the risk of accidents. If an infant ingests a battery, please seek immediate medical attention. Caution Remove and dispose of an old battery immediately. Do not disassemble, heat or short a battery. Do not thro a battery into a fire or ater. Follo local regulations hen disposing of a battery. Improper use of a battery may cause overheating, an explosion or ignition, resulting in injury or a fire. ote: Battery Information: Battery Type: Panasonic lithium battery (CR2025) (Included in the remote control) Battery Life: pproximately 6 months under normal use (at room temperature) E G LI H 18 Cancellation of Demonstration The demonstration message appears for initial use. et your car s ignition sitch to the CC or O position. The demonstration screen appears. Press [RC/PWR] to turn on the poer. e Press and hold [VOLUME] (PUH EL) for more than 2 seconds to open the menu. r Press [VOLUME] (PUH EL) to select the Demonstration setting. ( DEMO is displayed.) t Turn [VOLUME] counterclockise. (Press [0] ({) on the remote control unit.) ote: To return to the regular mode, press [D] (DIP). Refer to the section on Function ettings. (a Page 26) [D] (DIP/CLOCK) Main Unit Clock etting The 12-hour system is used for the clock. Press [RC/PWR] to turn on the poer. Press [D] (DIP/CLOCK). Clock display epress and hold [D] (DIP/CLOCK) for more than 2 seconds. Hour blinks rdjust the hour. [[]: put forard hour. []]: put back hour. Hour entered tpress [D] (DIP/CLOCK). Minute blinks ydjust the minute. [[]: put forard minute. []]: put back minute. Minute entered upress [D] (DIP/CLOCK). [VOLUME] (PUH EL: select) [RC/PWR] (Poer) []][[] (Hour/minute adjustment) Completed ote: DJUT is displayed before adjusting the clock. Press and hold [[] or []] to change numbers rapidly. 9

10 E G LI H 9 General [MUTE] (Mute/attenuation) [VOLUME] pectrum analyzer (a Page 26) CD Player mode display (a Page 17) Q3 indicator Remote control sensor (a Page 8) [RC/PWR] (ource/poer) [D] (DIP) (Display) [Q] (ound Quality) Preset Buttons [1] to [6] Poer et your car's ignition sitch to the CC or O position. O : Press [RC/PWR]. OFF : Press and hold [RC/PWR] until you hear a beep (approximately 1 second), then release it. ote: When the ignition sitch is set to O, the face plate is tilted to secure their former positions. If you turn the key to the CC OFF position during the security function is active, the security message appears ith a arning alarm. (Default: LED O) (a Page 28 about ecurity Function setting) Volume Don Up Default: 18 etting range: 0 to 40 ote: The volume level can be set independently for each source. (For radio, one volume setting for M, one volume setting for all FMs) Mute/ttenuation O : Press [MUTE]. OFF : Press [MUTE] again. You can select mute or attenuation. (a Page 26) indicator 10

11 E G LI ource Press [RC/PWR] to change the source. Radio CD Player OR MP3/WM Player UX1 n optional unit (ex. CD changer) (if you connect it to ystem-up Connector of this unit directly) (ound source connected to the ystem-up Connector of this unit directly a ystem Upgrade Guidebook) OR ome optional units (if you use the Expansion Module (CY-EM100U)) (hen connected) Port 1 (hen connected) Port 2 (hen connected) Port 3 (hen connected) Port 4 (a Page 14) (a Page 17) (When an MP3/WM data disc is in the player a Page 18) (ound source connecting to the UX input terminal a Page 28, Installation Instructions) (ound source connecting to the UX input terminal of Expansion Module a ystem Upgrade Guidebook) (ound source connected to the port 1 of Expansion Module a ystem Upgrade Guidebook) (ound source connected to the port 2 of Expansion Module a ystem Upgrade Guidebook) (ound source connected to the port 3 of Expansion Module a ystem Upgrade Guidebook) (ound source connected to the port 4 of Expansion Module a ystem Upgrade Guidebook) ote: For information about connectable devices, refer to the ystem Upgrade Guidebook or the instruction manual for each device. Q (ound Quality) You have 6 preset modes (FLT, ROCK, POP, VOCL, JZZ, CLUB). You can customize your setting for these (except Q-FLT) and save them for instant recall. Q3 (3-Band ound Quality) Center freuency and level are adjustable in each of 3 bands. This lets you fine-tune sound uality for each genre to suit car-interior acoustics and your personal preferences. (a Page 22) Press [Q] to activate the Q selection mode. Press [Q] to select the sound type as follos: Preset number (Default) (FLT) flat freuency response: does not emphasize any part. (ROCK) speedy and heavy sound: exaggerates bass and treble. (POP) ide-ranged and deep sound: slightly emphasizes bass and treble. (VOCL) clear sound: emphasizes middle tone and slightly emphasizes treble. (JZZ) jazz-specific deep sound: sound ith emphasis on sharpness of high-hat and echo of saxophone. (CLUB) club and disco-specific sound: reproduction of realism being in a club. Press [D] (DIP) to return to the regular mode. ote: fter pressing [Q] on the main unit, you can also select a sound type by pressing the preset buttons [1] to [6]. H

12 E G LI H 11 General (continued) Caution Do not pinch your finger or hand in the face plate. [u: Eject] (TILT/OPE) Open the Face Plate Press [u: Eject] (OPE). ote: The face plate automatically closes after a arning alarm sounds if no operation is performed for approximately 20 seconds. When a disc is already loaded, the disc ill be ejected after the face plate fully opens. (Disc Eject a Page 16) Close the Face Plate Press [u] (OPE). [D] (DIP/CLOCK) Face Plate ngle (Tilt) Press and hold [u] (TILT) until you hear a beep (approximately 1 second) from the speaker output, then release it. et the face plate to the position at hich it is easy to read hat is on the display. Each time the above operation is repeated, the face plate angle changes in the seuence shon belo. TILT 1 TILT 2 TILT 3 OPE TILT OFF ote: The positions specified at Face Plate ngle (Tilt) are memorized even after the folloing operations. Open/close CC on/off 12

13 E G LI Clock Display (at Poer off) When the poer of the unit is set to OFF, press [D] (DIP/CLOCK). H 12 (Clock time) (Default) (Display off) When the poer is set to O, refer to the description for each source mode. 13

14 E G LI Radio H 13 (tereo) indicator []][[] (TUE) [D] (DIP) (Display) [BD] (PM: uto Preset Memory) [RC/PWR] (ource) Radio Mode Press [RC/PWR] to select the radio mode. Preset Buttons [1] to [6] (Preset station) Display Change Press [D] (DIP) to change the display as follos. Freuency Band Band Press [BD]. Freuency Preset number Clock Time Display Off e Tuning [[]: Higher freuency []]: Loer freuency Press and hold [[] or []] for more than 0.5 seconds, then release it. eeking ill start. 14

15 E G LI H 14 1 tation Preset Up to 6 stations can be stored in each of the FM1, FM2, FM3 and M band selections. ote: e stations overrite existing saved stations after these procedures. Warning To ensure safety, never attempt to preset stations hile you are driving. uto Preset Memory (PM) With this operation, stations ith good receiving conditions can be automatically stored in the preset memory. elect a band. (a Previous page) Press and hold [BD] (PM) for more than 2 seconds. 6 stations ith first to 6th highest in signal strength ill be preset to each band. Once set, the preset stations are seuentially scanned for 5 seconds each. (scanning) Manual Preset Memory With this operation, a station can be manually stored in the preset memory. elect a band and freuency. (a Previous page) Press and hold one of the preset buttons from [1] to [6] until the display blinks once. Preset number ote: To stop scanning, press one of the buttons from [1] to [6]. elect a band. (a Previous page) Press one of the preset buttons from [1] to [6]. Preset tation Calling 15

16 E G LI Before Disc Playback H 15 Caution 8 cm {3 } discs are not available for this unit, therefore, do not insert them. Do not use irregularly shaped discs. Do not use discs that have a seal or label attached. To avoid damaging the face plate, do not push it don or place objects on it hile it is open. Do not pinch your finger or hand in the face plate. Do not insert foreign objects into the disc slot. vailable Discs CD-R CD-RW CD-TEXT CD-ROM CD-D CD-D CD-D MP3/WM MP3/WM MP3/WM ote: Refer to the section on otes on MP3/WM (a Page 20) and otes on Discs (a Page 31). The poer ill be turned on automatically hen a disc is loaded. disc hich has both CD-D data and MP3/WM data on it may not be reproduced normally. Disc Insert Press [u] (OPE). When a disc is already loaded ( lights), the disc ill be ejected after the face plate fully opens. Insert a disc. [u: Eject] (OPE) Printed ide ote: It may take some time to start playing. Playback ill start automatically after recognizing the data of the loaded disc. OR (a Page 18 about MP3/WM Player) Disc Eject Press [u] (OPE). The disc ill be ejected after the face plate fully opens. Take the disc out. e Press [u] (OPE) to close the face plate. ote: The face plate is automatically closed after a arning alarm sounds if no operation is performed for approximately 20 seconds. 16

17 CD Player E G LI indicator [s] / [d] (a / f) (Track selection/fast forard/fast reverse) [D] (DIP) (Display) H 16 1 [BD] (y / 5: Pause/play) When CD is in the player Press [RC/PWR] to select the CD player mode and playback starts. Display Change Press [D] (DIP). Track/Play time Disc title [3] (CROLL) [RC/PWR] (ource) Track Play time [5] (C) [4] (RDOM) [6] (REPET) Pause (y / 5) Press [BD] (y / 5). Press [BD] (y / 5) again to cancel. Random Play ll the available tracks are played in a random seuence. Press [4] (RDOM). lights. Press [4] (RDOM) again to cancel. can Play The first 10 seconds of each track is played in seuence. Press [5] (C). Track title Clock time Display off ote: O TEXT is displayed hen there is no information on the disc. To have another circle scroll hile a title is displayed, press [3] (CROLL). If the number of displayed characters is 8 or less, the characters do not scroll. Track election [d]: ext track [s]: Beginning of the current track For the previous track, press tice. Fast Forard/Fast Reverse Press and hold [d] (f): Fast forard [s] (a): Fast reverse Release to resume normal playback. Press [5] (C) again to cancel. Repeat Play The current track is repeated. Press [6] (REPET). lights. Press [6] (REPET) again to cancel. Direct Track election (Only for remote control unit) Example: Track number 10 Press [#]. Press [1] [0]. e Press [BD] (ET). ote: To suspend direct selection, press [DIP]. Random, can and Repeat plays are canceled once [#] is pressed. 17

18 E G LI H 17 MP3/WM Player indicator [s] / [d] (a / f) (File selection/fast forard/fast reverse) [{] / [}] (FOLDER) (Folder selection) [BD] (y / 5: Pause/play) [3] (CROLL) [RC/PWR] (ource) [5] (C) [4] (RDOM) [6] (REPET) When a disc is in the player Press [RC/PWR] to select the MP3/WM player mode and playback starts. [D] (DIP) (Display) *ID3/WM Tag etting Press and hold [3] (CROLL) for more than 2 seconds. Folder Display Change Press [D] (DIP). Folder/File Play time Folder name/album name* ( )(Data reading) File name/title and artist name* ( )(Data reading) Clock time Display off File ote: O TEXT is displayed hen there is no information on the disc. To have another circle scroll hile a title is displayed, press [3] (CROLL). If the number of displayed characters is 8 or less, the characters do not scroll. (Default) When a folder name is displayed: TG O: The album title is displayed. TG OFF: The folder name is displayed. When a file name is displayed: TG O: The title/artist name is displayed. TG OFF: The file name is displayed. Folder election [}]: ext folder [{]: Previous folder File election [d]: ext file [s]: Beginning of the current file For the previous file, press tice. Fast Forard/Fast Reverse Press and hold [d] (f): Fast forard [s] (a): Fast reverse Release them to resume normal playback. Pause (y / 5) Press [BD] (y / 5). Press [BD] (y / 5) again to cancel. 18

19 E G LI H 18 1 Random Play ll the available files are played in a random seuence. Press [4] (RDOM). lights. Press [4] (RDOM) again to cancel. Folder Random Play ll the files in the current folder are played in a random seuence. Press and hold [4] (RDOM) for more than 2 seconds. light. Press and hold [4] (RDOM) again for more than 2 seconds to cancel. can Play The first 10 seconds of each file is played in seuence. Press [5] (C). Repeat Play The current file is repeated. Press [6] (REPET). lights. Press [6] (REPET) again to cancel. Folder Repeat Play The current folder is repeated. Press and hold [6] (REPET) for more than 2 seconds. light. Press and hold [6] (REPET) again for more than 2 seconds to cancel. Direct election (Only for remote control) Direct Folder election Example: Folder number 10 (a Page 21) Press [5] (C) again to cancel. Folder can Play From the next folder, the first 10 seconds of the first file in each folder is played in seuence. Press and hold [5] (C) for more than 2 seconds. lights. Press and hold [5] (C) again for more than 2 seconds to cancel. Press [#] tice. Press [1] [0]. e Press [BD] (ET). Direct File election Example: File number 10 Press [#]. Press [1] [0]. e Press [BD] (ET). ote: To suspend direct selection, press [DIP]. Random, Folder Random, can, Folder can, Repeat and Folder Repeat plays are canceled once [#] is pressed. 19

20 E G LI otes on MP3/WM H What is MP3/WM? Display Information 19 MP3 (MPEG udio Layer-3) and WM (Windos Media TM udio) are the compression formats of digital audio. The former is developed by MPEG (Motion Picture Experts Group), and the latter is developed by Microsoft Corporation. Using these compression formats, you can record the contents of about 10 music CDs on a single CD (This figure refers to data recorded on a 650 MB CD-R or CD-RW at a fixed bit rate of 128 kbps and a sampling freuency of 44.1 khz). Displayed items CD-TEXT Disc title Track title MP3/WM Folder name File name MP3 (ID3 tag) lbum name Title and artist name WM (WM tag) lbum name Title and artist name ote: MP3/WM encoding and CD riting softare programs are not supplied ith this unit. Points to remember hen making MP3/WM files Common High bit rate and high sampling freuency are recommended for high uality sound. electing VBR (Variable Bit Rate) is not recommended because playing time is not displayed properly and sound may be skipped. The playback sound uality differs depending on the encoding circumstances. For details, refer to the instructions of your on encoding softare and riting softare. MP3 It is recommended to set the bit rate to 128 kbps or more and fixed. WM It is recommended to set the bit rate to 64 kbps or more and fixed. Do not set the copy protection on the WM file to enable this unit to play back. Caution ever assign the.mp3, or.ma file name extension to a file that is not in the MP3/WM format. This may not only produce noise from the speaker damage, but also damage your hearing. Displayable characters Displayable length of file name/folder name: ithin 64 characters. (Unicoded file and folder names are reduced by half in the number of displayable characters.) ame files and folders in accordance ith the standard of each file system. Refer to the instructions of riting softare for details. CII character set and special characters in each language can be displayed. ome Cyrillic characters in the Unicode can be displayed. CII character set to Z, a to z, digits 0 to 9, and the folloing symbols: (space)! # $ % & ( ) * +, -. / : ; < = [ \ ] ˆ _ ` { } ~ pecial characters À Á Â Ã Å à á â ã å Ä ä Ò Ó Ô Õ Ö ò ó ô õ ö Ù Ú Û Ü ù ú û ü ote: With some softare in hich MP3/WM format files have been encoded, the character information may not be displayed properly. Undisplayable characters and symbols ill be converted into an asterisk ( ). It is recommended that the length of the file name is less than 8 (excluding the file extension). 20

21 E G LI Recording Recording MP3/WM MP3/WM files on files a CD-media on a You are recommended to minimize the chances of making a disc that contains both CD-D files and MP3/WM files. If CD-D files are on the same disc as MP3 or WM files, the songs may not play in the intended order, or some songs may not play at all. When storing MP3 data and WM data on the same disc, use different folders for each data. Do not record files other than MP3/WM files and unnecessary folder on a disc. The name of an MP3/WM file should be added by rules as shon in the folloing descriptions and also comply ith the rules of each file system. The file extension.mp3 or.ma should be assigned to each file depending on the file format. You may encounter trouble in playing MP3/WM files or displaying the information of MP3/WM files recorded ith certain riting softare or CD recorders. This unit does not have a play list function. lthough Multi-session recording is supported, the use of Disc-at-Once is recommended. upported file systems IO 9660 Level 1/Level 2, pple Extension to IO 9660, Joliet, Romeo ote: pple HF, UDF 1.50, Mix CD and CD Extra are not supported. H 20 1 Compression formats (Recommendation: Points to remember hen making MP3/WM files on the previous page) Compression method Bit rate VBR ampling freuency MPEG 1 audio layer 3 (MP3) 32 k 320 kbps Yes 32, 44.1, 48 khz MPEG 2 audio layer 3 (MP3) 8 k 160 kbps Yes 16, 22.05, 24 khz Windos Media udio Ver. 2, 7, 8, 9* 32 k 192 kbps Yes 32, 44.1, 48 khz * WM 9 Professional/LossLess/Voice are not supported. Folder selection order/file playback order Maximum number of files/folders Maximum number of files/folders: 511 (files + folders) Maximum number of files in one folder: 255 Maximum depth of trees: 8 Maximum number of folders: 255 (Root folder is included.) ote: You can shorten the duration beteen data read and playback by decreasing the uantity of files or folders, or the depth of the hierarchy. This unit counts the number of folders irrespective of the presence or absence of an MP3/WM file. If the selected folder does not contain any MP3/WM files, the nearest MP3/WM files in the order of playback ill be played. Playback order may be different from other MP3/WM players even if the same disc is used. ROOT appears hen displaying the root folder name Root Folder (Root Directory) e r Folder election In the order 1 8 File election In the order 7 y Tree 1 Tree 2 Tree 3 Tree 4 Tree 8 (Max.) Copyright It is prohibited by copyright las to copy, distribute and deliver copyrighted materials such as music ithout the approval of copyright holder except enjoying yourself personally. t y o arranty bove description complies ith our investigations as of December It has no arranty for reproducibility and displayability of MP3/WM. 21

22 E G LI udio ettings H 21 Turn [VOLUME]. (Press [VOL }] or [VOL {] on the remote control unit.) [D] (DIP) (Return to the regular mode) [Q] (ound Quality) Volume Default: 18 etting range: 0 to 40 Preset Buttons [2] to [6] Press [VOLUME] (PUH EL: select). (Press [EL] on the remote control unit.) [[]/[]] [{] / [}] [BD] Press [VOLUME] (PUH EL) to open the menu. Bass/Treble You can adjust the bass and treble sounds. Default: B (bass) 0 db TRE (treble) 0 db etting range: 12 db to +12 db (by 2 db) Press [VOLUME] (PUH EL). Press [VOLUME] (PUH EL). Q djustment You can adjust the characteristics of the currently selected sound type (Q). (a Page 11) It is also possible to preset up to 5 different adjusted Qs. Tone/Q adjustable range: 12 db to +12 db (by 2 db) Q Lo/Bass : ± 12 db (at 60 Hz, 80 Hz, 100 Hz, 200 Hz) Q Mid : ± 12 db (at 500 Hz, 1 khz, 2 khz, 3 khz) Q High/Treble : ± 12 db (at 10 khz, 12 khz, 15 khz, 18 khz) The bass/treble control level of each freuency is fixed to the freuency that has been selected for Q. Press [VOLUME] (PUH EL). The Q adjustment mode can be established also by pressing [Q] for more than 2 seconds. FTo return an adjusted Q to the default setting Press [Q], and select the Q hich is to be returned to the default setting. (Only for main unit) Press and hold [BD] for more than 2 seconds. 22 (Page 24)

23 E G LI Regular mode VOLUME B TREBLE Q ET H 22 1 UBW LPF UBW LEV FDER BLCE ote: The seuence and contents of setting items may depend on the conditions of devices to be connected. For further information, refer to the ystem Upgrade Guidebook or the instruction manuals for the devices to be connected. To return to the regular mode, press [D] (DIP). If no operation takes place for more than 5 seconds in audio setting (2 seconds in the volume adjustment, 10 seconds in the Q adjustment), the display returns to the regular mode. The volume can also be adjusted directly using [VOLUME] on the main unit. (a Page 10) Please refer to page 11 for calling up a preset Q. Turn [VOLUME]. : Up : Don Turn [VOLUME]. : Up : Don Turn [VOLUME]. : Up : Don ote: You cannot save any Q presetting value in [1] button. ny Q adjustments ill not change the call up screen names such as ROCK and JZZ. Press [[] or []] to select a freuency band (Lo, Mid, High). [[]: Higher freuency band []]: Loer freuency band Turn [VOLUME] to select a freuency. : Higher freuency : Loer freuency Press [}] or [{] to adjust the level. [}]: Up [{]: Don e Press and hold one of the preset buttons from [2] to [6] for more than 2 seconds. The adjusted Q is preset in the number of the selected button, and return to the regular mode resumes. Freuency The selected freuency band blinks. Level When you suspend the Q preset adjustment, each level remains your recent adjustment until a ne Q presetting operation is performed or you call up the Q preset. 23

24 E G LI H 23 udio ettings (continued) Turn [VOLUME]. (Press [VOL }] or [VOL {] on the remote control unit.) Press [VOLUME] (PUH EL: select). (Press [EL] on the remote control unit.) [D] (DIP) (Return to the regular mode) Balance/Fader You can adjust the sound level among the right, left, front and rear speakers. Default: BL (balance) CT (center) FD (fader) CT (center) etting range: 15 levels each and CT (center) Press [VOLUME] (PUH EL). Press [VOLUME] (PUH EL). uboofer Level You can change the suboofer volume level. Default: 0 etting range: MUTE ( ), 6 db to + 6 db (by 2 db) uboofer LPF (Lo Pass Filter) You can select the upper limit freuency of the sound from suboofer. Default: 80 Hz etting range: 80 Hz, 120 Hz Press [VOLUME] (PUH EL). Press [VOLUME] (PUH EL). Regular mode 24

25 E G LI Regular mode VOLUME B TREBLE Q ET H 24 UBW LPF UBW LEV FDER BLCE ote: The seuence and contents of setting items may depend on the conditions of devices to be connected. For further information, refer to the ystem Upgrade Guidebook or the instruction manuals for the devices to be connected. To return to the regular mode, press [D] (DIP). If no operation takes place for more than 5 seconds in audio setting, the display returns to the regular mode. djustments of the suboofer level and lo pass filter are effective hen the suboofer is connected. Turn [VOLUME]. : Right enhanced : Left enhanced Turn [VOLUME]. : Front enhanced : Rear enhanced Turn [VOLUME]. : Up : Don Turn [VOLUME]. : 120 Hz : 80 Hz 25

26 E G LI H 25 Function ettings Turn [VOLUME]. (Press [8] (}) or [0] ({) on the remote control unit.) [D] (DIP) (Return to the regular mode) Press and hold [VOLUME] (PUH EL: select) for more than 2 seconds. (Press and hold [EL] (MEU) for more than 2 seconds on the remote control unit.) Demonstration You can set up the monitor to display or hide the demonstration screen. Default: O Press and hold [VOLUME] (PUH EL) for more than 2 seconds to open the menu. Dimmer (display brightness setting) You can adjust the display brightness. Default: DIMMER 3 Variety: DIMMER 1 3 Press [VOLUME] (PUH EL). pectrum nalyzer Display Patterns (PTTER) Default: Pattern 1 Variety: 6 types, OFF Press [VOLUME] (PUH EL). Mute/ttenuation You can select mute or attenuation. (a Page 10) Default: MUTE Press [VOLUME] (PUH EL). 26 (Page 28)

27 E G LI Regular mode DEMO ECURITY DIMMER UX1 I PTTER MUTE KEY H 26 1 ote: The seuence and contents of setting items may depend on the conditions of devices to be connected. For further information, refer to the ystem Upgrade Guidebook or the instruction manuals for the devices to be connected. To return to the regular mode, press [D] (DIP). If no operation takes place for more than 5 seconds in function setting, the display returns to the regular mode. Turn [VOLUME]. : On (Default) : Off ote: Button operation ith either the main unit or remote control allos users to cancel the demonstration screen for 20 seconds and enable the selected operation even in the demo-on mode. Turn [VOLUME]. : Darker : Medium : Brighter (Default) Turn [VOLUME]. : Off : Pattern 1 (Default) : Pattern 6 Turn [VOLUME]. : 10 steps decrease (ttenuation) : o sound (Mute) (Default) 27

28 E G LI H 27 Function ettings (continued) Turn [VOLUME]. (Press [8] (}) or [0] ({) on the remote control unit.) [D] (DIP) (Return to the regular mode) Press and hold [VOLUME] (PUH EL: select) for more than 2 seconds. (Press and hold [EL] (MEU) for more than 2 seconds on the remote control unit.) UX kip If UX1 is not used, the UX mode is skipped hen selecting the source. Default: O (kip disabled) Press [VOLUME] (PUH EL). ecurity Function You can activate the anti-theft function hen leaving your car. Default: O Press [VOLUME] (PUH EL). (Page 26) 28

29 E G LI Regular mode DEMO ECURITY DIMMER UX1 I PTTER MUTE KEY H 28 ote: The seuence and contents of setting items may depend on the conditions of devices to be connected. For further information, refer to the ystem Upgrade Guidebook or the instruction manuals for the devices to be connected. To return to the regular mode, press [D] (DIP). If no operation takes place for more than 5 seconds in function setting, the display returns to the regular mode. Turn [VOLUME]. : kip disabled (Default) : kip enabled Turn [VOLUME]. The security function is activated. (Default) The security function is not activated. LED (ecurity Light Emitted Diode) O When the ignition sitch is turned OFF... The security message ill be displayed. The face plate removal alarm ill be active. (a Page 30) When the face plate is removed... The security indicator (LED) blinks. (a Page 30) 29

30 E G LI nti-theft ystem H 29 This unit is euipped ith a removable face plate. Removing this face plate makes the unit totally inoperable. LED ill blink. Remove the Face Plate itch off the poer of the unit. Press [ ](release) to remove the face plate. (The face plate disengages ith a click hen it is removed.) e Place the face plate into the case and take it ith you hen you leave the car. [ ](Release) Removable Face Plate Case Contact ote: Be absolutely sure to turn off the poer of the unit before removing the face plate. Do not install or remove the face plate hile it is moving. Install the Face Plate Contact lide the left side of the face plate in place. Press the right end of the face plate until a click is heard. 1 2 ecurity Indicator (LED) LED blinks hen the face plate is removed from the unit. This function is activated hen the ecurity Function is O. (a Page 28) Face Plate Removal larm This alarm sounds to arn you not to forget to remove the face plate before leaving your car. This function is activated hen the ecurity Function is O. (a Page 28) LED Caution This face plate is not aterproof. Do not expose it to ater or excessive moisture. Do not remove the face plate hile driving your car. Do not place the face plate on the dashboard or nearby areas here the temperature rises high. Do not touch the contacts on the face plate and on the main unit, since this may result in poor electrical contact. If dirt or other foreign substances get on the contacts, ipe them off ith a clean and dry cloth. To avoid damaging the face plate, do not push it don or place objects on it hile it is open. The face plate ill automatically close about 5 seconds after [ ](release) is pressed hile the face plate is tilted or open, so take care to ensure that your fingers ill not be pinched by the closing face plate. 30