Méthode EXAO EXAO method Français p 1 English p 5 Photodiode BPW34 BPW34 photodiode Version : 6006
Méthode EXAO Photodiode BPW34 Sommaire 1. Présentation 2 2. Caractéristiques 2 3. Chaîne de mesure, réglages et courbe d étalonnage 2 3.1. Chaîne de mesure 2 3.2. Réglages 2-3 3.3. Fonction de transfert et courbe d étalonnage 3 FRANÇAIS 1
Méthode EXAO Photodiode BPW34 1 Présentation La photodiode BPW34 est un capteur linéaire d éclairement. 2 Caractéristiques Surface sensible...7.00 mm² Sensibilité spectrale...typ. 80 na/ix ( 50 na/ix) Gamme spectrale...400 à 1100 nm Longueur d onde de sensibilité maximale...850 nm Courant d obscurité...typ. 2 na ( 30 na) Efficacité quantique...0.90 électron/photon Température d utilisation...-40 à +85 C 3 Chaîne de mesure, réglages et courbe d étalonnage Le montage qui suit a pour objectif l obtention d une tension comprise entre 0 et 5 V qui soit l image de l éclairement sur une plage de 0 à 3000 lux. Le schéma indiqué ci-dessous permet cette amplification. Les explications qui le suivent se basent sur les fonctionnalités de la «Platine MPI» (Réf. 185 321). La fonction de transfert après amplification est ensuite donnée ainsi sue la courbe d étalonnage. 3.1 Chaîne de mesure 3.2 Réglages Le courant inverse en obscurité est donné à 2nA. Cela donne une tension résiduelle de 3900*2.10-9 = 7,8μV. Cette tension peut être négligée. FRANÇAIS 2
Méthode EXAO Photodiode BPW34 Le gain de l amplificateur est fixé à 5. Avec en sortie Vs = 5V, on a Vc = 1V et le courant inverse dans la photocopie I R = 1 / 3900 = 256μA. Cette valeur d intensité correspond à un éclairement d environ 3000lux. Le montage amplificateur à gain positif permet d obtenir un gain de 5 en ajustant la résistance de contre réaction à 40 kω. Oter le cavalier de l amplificateur, placer les pointes de touche d un ohmmètre sur les points test, régler la valeur de la résistance de contre réaction en utilisant les deux résistances ajustables, puis remettre le cavalier. La résistance de 200 kω permet d atteindre rapidement la valeur souhaitée. La résistance de 10 kω permet de faire un réglage fin. 3.3 Fonction de transfert et courbe d étalonnage Ev : Eclairement (lux) Vs : Tension de sortie de la chaîne d amplification (V) 4 Service après vente La garantie est de 2 ans, le matériel doit être retourné dans nos ateliers. Pour toutes réparations, réglages ou pièces détachées, veuillez contacter : JEULIN - SUPPORT TECHNIQUE Rue Jacques Monod BP 1900 27 019 EVREUX CEDEX FRANCE +33 (0)2 32 29 40 50 FRANÇAIS 3
Méthode EXAO Photodiode BPW34 NOTES FRANÇAIS 4
EXAO method BPW34 photodiode Contents 1. Presentation 6 2. Characteristics 6 3. Measuring system, adjustments and calibration curve 6 3.1. Measuring system 6 3.2. Adjustments 6-7 3.3. Transfer function and calibration curve 7 ENGLISH 5
EXAO method BPW34 photodiode 1 Presentation The BPW34 photodiode is a linear illumination sensor. 2 Characteristics Sensitive area... 7.00 mm 2 Spectral sensitivitytyp.... 80 na/lx ( 50 na/lx) Spectral range... 400 to 1100 nm Wavelength of maximum sensitivity... 850 nm Dark currenttyp.... 2 na ( 30 na) Quantum efficiency... 0.90 electron/photon Operating temperature... -40 to +85 C 3 Measuring system, adjustments and calibration curve The objective of the following set-up is to obtain a voltage between 0 and 5 V, which is the image of the illumination in a range of 0 to 3000 lux. The diagram shown below enables this amplification. The explanations that follow are based on the functionality of the "MPI Mounting Plate" (Part no. 158 321). The transfer function after amplification as well as the calibration curve are given thereafter. 3.1 Measuring system Sensor input +5V 10 kω Amplifier 40 kω BPW34 - + 3.9 kω V C V S 3.2 Adjustments The reverse dark current is 2nA. This gives a residual voltage of 3900 * 2.10-9 = 7.8µV. This voltage may be neglected. ENGLISH 6
EXAO method BPW34 photodiode The amplifier gain is fixed at 5. With an output voltage V S = 5V, V C = 1V and the reverse current in the photodiode is I R = 1 / 3900 = 256µA. This current value corresponds to an illumination of about 3000lux. The positive gain amplifier set-up helps obtain a gain of 5 by adjusting the degenerating resistor to 40 kω. Remove the jumper of the amplifier, place the tips of the ohmmeter on the test points, adjust the value of the degenerating resistor by using the two adjustable resistors and then put the jumper back. A resistance of 200 kω helps quickly attain the desired value. A resistance of 10 kω helps carry out fine adjustments. Transfer function and calibration curve V = 0,001625. S E V VS E V = 0,001625 E V : Illumination (lux) V S : Output voltage of the amplification system (V) Theoretical curve 4 After-sales service The device is under a 2-year guarantee, it must be sent back to our workshops. For any repairs, adjustments or spare parts, please contact: JEULIN TECHNICAL SUPPORT Rue Jacques Monod BP 1900 27 019 EVREUX CEDEX FRANCE +33 (0)2 32 29 40 50 ENGLISH 7
EXAO method BPW34 photodiode NOTES ENGLISH 8
Assistance technique en direct Une équipe d experts à votre disposition du Lundi au Vendredi (8h30 à 17h30) Direct connection for technical support A team of experts at your disposal from Monday to Friday (opening hours) Vous recherchez une information technique? Vous souhaitez un conseil d utilisation? Vous avez besoin d un diagnostic urgent? Nous prenons en charge immédiatement votre appel pour vous apporter une réponse adaptée à votre domaine d expérimentation : Sciences de la Vie et de la Terre, Physique, Chimie, Technologie. You re looking for technical information? You wish advice for use? You need an urgent diagnosis? We take in charge your request immediatly to provide you with the right answers regarding your activity field : Biology, Physics, Chemistry, Technology. Service gratuit * : + 33 (0)2 32 29 40 50 * Hors coût d appel Free service * : + 33 (0)2 32 29 40 50 * Call cost not included Aide en ligne : www.jeulin.fr Rubrique FAQ Rue Jacques-Monod, Z.I. n 1, Netreville, BP 1900, 27019 Evreux cedex, France Tél. : + 33 ( 0 )2 32 29 40 00 Fax : + 33 ( 0 )2 32 29 43 99 Internet : www.jeulin.fr - support@jeulin. fr Phone : + 33 ( 0 )2 32 29 40 49 Fax : + 33 ( 0 )2 32 29 43 05 Internet : www.jeulin.com - export@jeulin.fr SA capital 3 233 762 - Siren R.C.S. B 387 901 044 - Siret 387 901 04400017