Prisinter-variateur mobile 882 03 / 70 Caractéristiques Charges Tension 100-240 V± Fréquence 50-60 Hz Norme Courant porteur EN 50065 IEC 60669-2-1 + 5 C à + 45 C 110 V 250 W 250 W 230 V 500 W 500 W Lampe incandescente Lampe halogène Protection par dispositif électronique : - En cas de court-circuit ou de très forte surcharge, la prisinter-variateur mobile se met hors service. Après élimination du défaut, le produit est à nouveau fonctionnel. Branchement 882 03 882 70 Configuration d usine A la première mise sous tension l appui sur les touches ON ou OFF commande l ensemble des points d éclairage de l installation In One by Legrand. L appui sur Learn (1) annule cette fonction de commande générale. (1) Touche de programmation ou apprentissage. N0064FJ4/01
Description Média de communication PLC => Courant porteur N d'identification Touche Touches de commandes Fonctionnement La prisinter-variateur mobile : - peut commander simultanément à partir de ses touches ON, OFF, un ensemble de produits (acteurs) qui lui sont associés lors de son apprentissage (1), elle est alors Leader du scénario (2). - peut être commandée par d autres produits leaders, elle est alors Acteur du scénario. - peut communiquer avec des produits radio à travers l interface RF / PLC réf. 03606 / 29. En Leader : La prisinter-variateur mobile permet de commander à partir des touches ON et OFF: - les points d éclairage reliés aux autres produits qui lui sont associés (les acteurs), lors de l apprentissage. Remarque : seul l apprentissage de la touche ON est nécessaire, la touche OFF est apprise automatiquement. En Acteur : La prisinter-variateur mobile peut participer à 16 scénarios différents, en exécutant localement les commandes ON, OFF, + et - demandées par les produits leaders. En local : La prisinter-variateur mobile permet de commander le point d éclairage à partir des touches ON, OFF, + et -, qui est branché sur la prise. Réglage du niveau lumineux de la touche ON (hors procédure d apprentissage) : - régler le niveau lumineux à l aide des touches + et -, - appuyer simultanément sur les touches + et ON durant 5 secondes - la charge s éteint et se rallume au niveau ON. Le niveau ON est alors enregistré. Pour enregistrer un niveau lumineux lors de l apprentissage, l étape 2 de l Apprentissage du scénario devient : (sur l acteur) la touche de commande ON qui doit être associée au leader la touche de commande + ou - pour régler le niveau d'éclairage souhaité (1) Apprentissage : action d associer des produits en vue de les commander simultanément à partir d un point central. Cette association se réalise en appliquant la procédure d apprentissage du scénario en page 3. (2) Scénario : correspond à l ensemble des produits (acteurs) qui sont associés à une touche de commande. 2
Apprentissage du scénario Etape 1 : débuter l'apprentissage (sur le LEADER) Etape 2 : ajouter un acteur au scénario (sur l'acteur) Etape 3 : enregistrer le scénario (sur le LEADER) la touche de commande qui doit piloter le scénario la touche de commande qui doit être associée au leader Les voyants de tous les produits s'éteignent. Le scénario est enregistré. Pour ajouter plusieurs produits au scénario, répéter pour chaque acteur les opérations et. Modification d un scénario Etape 1 : ouvrir le scénario (sur le LEADER) la touche de commande qui pilote le scénario Les voyants de tous les produits du scénario clignotent. Etape 2 : modifier l'état d'un acteur du scénario (sur l'acteur) ou Pour supprimer le produit du scénario passer à l'étape 3 la touche de commande que l'on souhaite associer Etape 3 : enregistrer le scénario (sur le LEADER) Les voyants de tous les produits s'éteignent. Le scénario est enregistré. Effacement d un scénario Effacer tous les scénarios liés à la touche de commande (sur le LEADER) Effacer tous les scénarios liés à ce produit (sur le LEADER) la touche de commande et maintenir 10s et maintenir 10s 5 s 5 s Le scénario est effacé Retour du produit en configuration usine Légende Le voyant s'éteint Le voyant clignote lentement Le voyant clignote rapidement Le voyant flashe 3
4
Mobile dimmable plug 882 03 / 70 Characteristics Loads Voltage 100-240 V± Frequency 50-60 Hz Standard PLC EN 50065 IEC 60669-2-1 + 5 C to + 45 C 110 V 250 W 250 W 230 V 500 W 500 W Incandescent lamp Halogen lamp Protection by electronic device: - In the event of short circuit or very high overload, the mobile dimmable plug cuts out. Once the defect is eliminated, the product resumes its function. Connection 882 03 882 70 Factory settings On first powering up, pressing the buttons ON or OFF controls all of the lightning points of the In One by Legrand installation. Pressing the button (1) cancels this functionality. (1) Programming or learning button. 5
Description Communication media PLC => Power line carrier Identification No. button Control buttons Operation The mobile switchable plug: - can control simultaneously, via the ON, OFF, buttons, a set of products (actors) that it was linked to during learning (1) ; it is then Leader of the scenario (2). - can be controlled by other leader products; it is then an Actor of the scenario. - can communicate with radio frequency products via the RF / PLC interface, Cat. No. 03606 / 29. As Leader: The mobile switchable plug allows to control via the ON and OFF buttons: - lighting points connected to the other products associated with it (the actors) during learning. Note: learning is required only for the ON button, the OFF button is learnt automatically. As Actor: The mobile switchable plug can take part in up to 16 different scenarios, by locally executing the ON, OFF, + and - controls issued by the leader products. In local mode: The mobile switchable plug allows to control via the ON, OFF, + and - buttons the lighting point connected to the plug. Setting the light level of the ON button (excluding learning procedure) : - Set the level using the + and - buttons - Press the + and ON buttons at the same time, for 5 seconds - The load will extinguish and light up again at the ON level The ON level is now saved. To save a light level during learning, stage 2 of Scenario learning becomes: Press (on the actor) Press the ON control button that is to be linked to the leader Press the + or - control buttons to set the desired light level (1) Learning: action of linking product to be controlled simultaneously from a central point. This linking is performed by applying the Scenario learning procedure on page 7. (2) Scenario: corresponds to all the products (actors) that are linked to a control button. 6
Learn scenario Step 1: Start the learn phase (on the LEADER) Press Step 2: Add an actor to the scenario (on the ACTOR) Press Step 3: Record the scenario (on the LEADER) Press Press the command key that is to control the scenario Press the command key that is to be associated with the leader The indicator lamps of all the products go off. The scenario is recorded. To add a number of products to the scenario, repeat operations and for each actor. Modification of a scenario Step 1: Open the scenario (on the LEADER) Press Press the command key that controls the scenario The indicator lamps of all the products in the scenario blink. Step 2 : Modify the state of an actor in the scenario (on the ACTOR) Press Press Press the command key or that is to be associated To remove the product from the scenario, go to step 3 Step 3 : Record the scenario (on the LEADER) Press The indicator lamps of all the products go off. The scenario is recorded. Clearing a scenario Clear all the scenarios linked with the command key (on the LEADER) Press Press the command key and hold it down for 10 s 5 s The scenario is cleared Clear all the scenarios linked to this product (on the LEADER) Press Press and hold down for 10 s 5 s Return the product to factory configuration Key The indicator lamp goes off The indicator lamp blinks slowly The indicator lamp blinks quickly The indicator lamp flashes 7