ASSEMBLY INSTRUCTIONS SWING BED RONA CODE: 3811502 ITEM# L-GZ37PST-WTN
Parts List A Top Connection 1 Q Hook 2 B Beam for big roof R Small canopy 1 C Long beam 2 S Large canopy 1 D Short beam 2 E1 Post 1 1 E2 Post2 1 E3 Post 3 1 T Bolster 2 U Big pillow 2 V Small pillow 1 W Cushion 1 E Post 1 X Bib 2 F Middle beam 1 G Back rail 1 H Side rail 2 AA 5/16-18*2.125 Bolts BB 5/16-18*0.75 Bolts CC 5/16-18 Nuts 12 8 I Front supporter 1 J Back supporter 1 K Seat frame 1 DD 5/16-18*1.75 Bolts EE 1/ -20*1. Bolts FF 1/ -20*1.25 Bolts 6 L Back frame 1 GG 1/ -20 Nuts 6 M1 Left arm 1 HH 3/16-2*0. Bolts M2 Right arm 1 II Nails 5/16"*7 8 N Adjusting bar 1 JJ Allen key 1/ -20 1 KK Wrench 1 O Suspender 1/ -20/5/16-18 P Latch MM Bolts 1/"-20*2 2 PP Bolts (preassembled) 2 NN Plastic washer 2
Step1: (1) Connect middle beam (F) to short beam (D) with bolts (AA), nuts (CC). ( Fig.1) (2) Insert the each side of long beam (C) into the top hold of post 1(E1), post 2(E2), post 3 (E3), post (E), and then insert short beam (D) into the top hold of post 1(E1), post 2(E2), post 3 (E3), post (E). (Fig.2) (3) Tighten side rail (H) onto post 1 (E1), post 2 (E2), post 3 (E3), post (E) with bolts (BB). ( Fig.2) () Tighten back rail (G) onto post 1 (E1), post (E) with bolts (BB). ( Fig.)
Step 2: (5) Insert one of side of beam for big roof (B) into the hole of top connection (A). (Fig.5) (6) Spread the small canopy (R) and large canopy (S), don t spread the large canopy fully at this time (Fig.6) (7) Screw beam of big roof (B) and post1 (E1), post 2 (E2), post 3 (E3), post (E) with bolts (EE), nuts (GG). (Fig7)
Step 3: (8) Connect front supporter (I), left arm (M1) and right arm (M2) with bolts (FF). (Fig8) (9) Connect back supporter (J), left arm (M1) and right arm (M2) with bolts (FF). (Fig9) (10) Tighten seat frame (K) and back frame (L) with bolts (DD), nuts (CC). (Fig10) (11) Connect seat frame (K), left arm (M1) and right arm (M2) with bolts (DD), plastic washer (NN),nuts (CC). (Fig11) (12) Tighten back frame (L) with the bolts (PP). (Fig12) Note: Do this step only if you will use this unit as a bed.
Step : (13)Connect seat frame adjusting bar (N) and back frame (L) with bolts (MM), nuts (GG). (Fig13) (1)Lay the adjustable support of the adjusting bar (N) on the back supporter (J). (Fig1) (15)Hang one of the side of suspender (O) onto the hooks of arm left (M1) and arm right (M2). (Fig15)
Step 5: (16)Fix one side of suspender (O) onto hook (Q), the other side onto middle beam (F,) then cover hook (Q) with bib (X). (Fig.16) (17) Place swing cushion (W) and bolster (T), big pillow (U) small pillow (V) on the seat and back. (18) Spread the large canopy (S) fully. (19) Secure the post 1 (E1), post 2 (E2), post 3 (E3), post (E), using nails (II) to fasten the product. (Fig.19) (20) Fasten latch (P) and side rail (H) with bolts (HH). (Fig.20) Maintenance: 1. This swing bed is not a permanent structure and should be disassembled & stored away after use. 2. Do not repack your swing bed until it is completely dry. 3. This swing bed must be assembled by two adults or more.. This swing bed must not be left erect in high wind conditions. Made in China
INSTRUCTIONS DE MONTAGE LIT-BALANÇOIRE CODE RONA: 3811502 ARTICLE No. L-GZ37PST-WTN
Liste de pièces A Connexion du toit 1 Q Crochet 2 B Poutre du grand Toit R Petit auvent 1 C Poutre longue 2 S Grand auvent 1 D Poutre courte 2 T Polochon 2 E1 Poteau 1 1 U Grand coussin 2 E2 Poteau 2 1 V Petit coussin 1 E3 Poteau 3 1 W Coussin de balançoire 1 E Poteau 1 X Tablier 2 F Poutre centrale 1 AA Boulons 5/16-18*2.125 G Balustre arrière 1 BB Boulons 5/16-18*0.75 12 H Balustre latéral 2 CC Écrous 5/16-18 8 I Support avant 1 DD Boulons 5/16-18*1.75 J Support arrière 1 EE Boulons 1/ -20*1. K Cadre du siège 1 FF Boulons 1/ -20*1.25 6 L Cadre du dossier 1 GG Écrous 1/ -20 6 M1 Accoudoir gauche 1 HH Boulons 3/16-2*0. M2 Accoudoir droit 1 II Clous 5/16"*7 8 N Barre 1 JJ Clé (Allen.) 1 d ajustement 1/ -20 O Suspente KK Clé 1 1/ -20/5/16-18 P Loquet MM Boulons 1/"-20*2 2 PP Boulons (préassemblées) 2 NN Plates 2
Étape 1: 1. Connectez la poutre centrale (F) à la poutre courte (D) avec des boulons (AA), et écrous (CC). (Fig.1) 2. Introduisez chaque extrémité de la poutre longue (C) dans les connexions supérieures du poteau 1 (E1), poteau 2 (E2), poteau 3 (E3), poteau (E), et puis Introduisez chaque extrémitéde la poutre courte (D) dans les connexions supérieures du poteau 1 (E1), poteau 2 (E2), poteau 3 (E3), poteau (E), (Fig.2) 3. Fixez le balustre latéral (H) au poteau 1 (E1), poteau 2 (E2), poteau 3 (E3), poteau (E) avec des boulons (BB) (Fig.2).. Fixez le balustre arrière (G) au poteau 1 (E1), et poteau (E) avec des boulons (BB) (Fig.).
Étape 2: 5. Introduisez une extrémité de la poutre du grand toit (B) dans un des trous de la connexion du toit (A) (Fig.5). 6. Étalez le petit auvent (R) et le grand auvent (S), mais n étendez pas complètement le petit auvent (Fig.6). 7. Boulonnez la poutre du grand toit (B) au poteau 1 (E1), poteau 2 (E2), poteau 3 (E3), poteau (E) avec des boulons (EE), et écrous (GG) (Fig7).
Étape 3: 8. Connectez le support avant (I), à l accoudoir gauche (M1) et à l accoudoir droit (M2) avec des boulons (FF) (Fig.8). 9. Connectez le support arrière (J), à l accoudoir gauche (M1) et à l accoudoir droit (M2) avec des boulons (FF) (Fig.9). 10. Fixez le cadre du siège (K) et le cadre du dossier (L) avec des boulons (DD), et écrous (CC) (Fig.10). 11. Connectez le cadre du siège (K), à l accoudoir gauche (M1) et à l accoudoir droit (M2) avec des boulons (DD), plates (NN), et écrous (CC) (Fig.11). 12. Fixez le cadre du dossier (L) avec des boulons (PP) (Fig.12). Avis: N effectuez pas cette étape si vous n allez pas utiliser ce meuble comme lit.
Étape : 13. Connectez la barre d ajustement du siège (N) au cadre du dossier (L) avec des boulons (MM), et écrous (GG) (Fig.13). 1. Posez le support réglable de la barre d ajustement (N) sur le support arrière (J) (Fig.1). 15. Accrochez une des extrémités de la suspente (O) sur le crochet de l accoudoir gauche (M1) et de l accoudoir droit (M2) (Fig15).
Étape 5: 16. Fixez une des extrémités de la suspente (O) sur le crochet (Q), l autre extrémité sur la poutre centrale (F,) ensuite couvrez le crochet (Q) avec le tablier (X) (Fig.16). 17. Posez le grand coussin (de balançoire) (W), les polochons, (T), les grands coussins (U) et petits coussins (V) sur le cadre du siège et du dossier. 18. Étirez (S) complètement le grand auvent.. 19. Fixez le poteau 1 (E1), Poteau 2 (E2), poteau 3 (E3), poteau (E) au sol, avec les clous (II) pour ancrer l article (Fig.19). 20. Installez le loquet (P) au balustre latéral (H) avec boulons (HH) (Fig.20). Entretien: 1. Cette balançoire n est pas une structure permanente et doit être démontée et rangée après l emploi. 2. Ne rangez pas la balançoire avant qu elle ne soit complètement sèche. 3. Deux adultes ou plus seront nécessaires pour monter cette balançoire. Cette balançoire ne doit pas être laissée en position érigée quand il y a du vent fort. Fait en Chine