INSTALLATION MANUAL 00USB Upper Shelf Black 00LSB Lower Shelf Black For use with Valor models LX 00J Fireplaces ONLY Note: This kit must be installed by a qualifi ed installer. These instructions are to be used in conjunction with the main installation instructions for the above listed models. of Kit These instructions cover the installation of both shelf kits on the -sided LX fi replace. The 00USB Upper Shelf Kit is installed above the opening of the LX -sided fi replace. The 00LSB Lower Shelf Kit is installed below the opening of the LX -sided fi replace. Each kit contains the shelf and the mounting brackets.! The shelves should be installed BEFORE the wall finish is applied. Wall finish then butts up to the shelves. Shelves CANNOT be installed over top of wall finish material. LX Series Overview Kits Contents 00USB Upper Shelf 00LSB Lower Shelf LH bracket LH bracket End caps () End caps () Upper shelf RH bracket Lower shelf RH bracket Hardware 8 #8-/8 sheet metal screws M6 x 0 mm bolts Washers Hardware 6 #8-/8 sheet metal screws M6 x 0mm bolts Washers 00777-0 08, Miles Industries Ltd. All rights reserved.
Dimensions -/ (96 mm) 8-/ (6 mm) 9-/ (89 mm) Upper shelf 60-/8 (5 mm) Lower shelf 6-/8 (585 mm) (0 mm) / (9 mm) (05 mm) -/6 (06 mm) -/ ( mm) 7 ( mm) 5-/6 ( mm) -/6 (9 mm) 5-5/8 ( mm) 5-/6 (9 mm) Wall finish considerations around shelves Shelves are installed directly over fi replace outer case They should be installed BEFORE the wall fi nish is applied. Wall fi nish then butts up to the shelves. Shelves CANNOT be installed over top of wall fi nish material. Wall finish material Non-combustible materials Upper shelf thickness -/ ( mm) Lower shelf thickness 5-5/8 ( mm)
Installation. Install brackets to liner box. Ensure proper orientation of brackets. Upper shelf: one bracket secured by sheet metal screws each side.. Orientation of shelf can be identifi ed from its internal support bracket: bracket is attached to bottom of shelf. top Internal support brackets attached to the bottom of the shelf bottom Identify top and bottom of shelf to install. Line up shelf and slide it over brackets on each side of appliance case. Upper shelf: Upper shelf rests on fi replace opening s upper fl ange. Do not force shelf into place as this may cause cracking. Lower shelf: one bracket secured by 8 sheet metal screws each side. Lower shelf: Lower shelf rests on brackets fl ange. Do not force shelf into place as this may cause cracking.
. Secure shelf from its rear opening, fastening inner shelf bracket to bracket installed on fi replace with one washer and one screw. This can be done by hand if there is no space for a screwdriver. Do not overtighten as this may cause cracking. Repair Parts List 00USB Upper Shelf Black Part no. Upper shelf 0065 LH bracket 00665 RH bracket 00666 End caps () 0066 #8-/8 Sheet metal screws (8) M6 x 0mm Bolts () Washers (). Fit shelf s end caps on both sides, inserting inside edge fi rst then outside edge as indicated. install with gap outward 00LSB Lower Shelf Black Part no. Lower shelf 006 LH bracket 0069 RH bracket 0069 End caps () 006 #8-/8 Sheet metal screws (6) M6 x 0mm Bolts () Washers () 5. Protect shelves from damage during wall fi nish application by using masking tape or plastic fi lm between wall fi nish and shelf. Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication. Designed and Manufactured by / for Miles Industries Ltd. 90 55 Dollarton Highway, North Vancouver, B.C., CANADA V7H B Tel. 60-98-96 Fax 60-98-06 www.valorfireplaces.com
DIRECTIVES D INSTALLATION LE PREMIER MC FOYER À GAZ RADIANT Série LX Tablette supérieure noire 00USB Tablette inférieure noire 00LSB Pour foyers Valor LX 00 à côtés SEULEMENT Note : Cette tablette doit être installée par un installateur qualifi é. Ces directives doivent être utilisées conjointement avec les directives d installation des modèles mentionnés ci-haut. Concept Ces directives couvrent l installation des tablettes supérieure et inférieure sur les foyers LX à côtés. La Tablette supérieure 00USB s installe au-dessus de l ouverture du foyer. La Tablette inférieure 00LSB s installe en-dessous de l ouverture du foyer. Chaque trousse contient la tablette, les montants et la quilcaillerie nécessaires à l installation. Les tablettes doivent être installées AVANT! la finition du mur. La finition du mur aboute aux tablettes. Les tablettes NE PEUVENT être installées par-dessus la finition du mur. Contenu des trousses Tablette supérieure 00USB Tablette inférieure 00LSB Support gauche Couvercles du bout () Support gauche Couvercles du bout () Tablette supérieure Support droit Tablette inférieure Support droit Quincaillerie 8 vis à métaux n o 8-/8 boulons M6 x 0 mm rondelles Quincaillerie 6 vis à métaux n o 8-/8 boulons M6 x 0 mm rondelles 5
Dimensions -/ (96 mm) 8-/ (6 mm) 9-/ (89 mm) Tablette supérieure 60-/8 (5 mm) Tablette inférieure 6-/8 (585 mm) (0 mm) / (9 mm) (05 mm) -/6 (06 mm) -/ ( mm) 7 ( mm) 5-/6 ( mm) -/6 (9 mm) 5-5/8 ( mm) 5-/6 (9 mm) Finition du mur autour des tablettes considérations Les tablettes sont installées directement sur la caisse extérieure du foyer. Elles doivent être installées AVANT la fi nition du mur. La fi nition du mur aboute aux tablettes. Les tablettes NE PEUVENT être installées par-dessus la fi nition du mur. Matériaux de finition du mur Matériaux incombustibles Épaisseur tablette supérieure -/ ( mm) Épaisseur tablette inférieure 5-5/8 ( mm) 6
Installation. Installez les supports sur la caisse du foyer. Assurez-vous qu ils soient bien orientés. Tablette supérieure : un support fi xé par vis à métaux de chaque côté.. L orientation de la tablette peut être identifi ée par son support interne : le support interne est fi xé sur le bas de la tablette. haut Support interne fi xé au bas de la tablette bas Identifi ez le haut et le bas de la tablette. Alignez la tablette avec les supports sur la caisse de foyer et glissez-la sur ces supports. Tablette supérieure : repose sur le rebord supérieure de l ouverture du foyer. Ne forcez pas la tablette en place car elle pourrait craquer. Tablette inférieure : un support fi xé par 8 vis à métaux de chaque côté. Tablette inférieure : repose sur le rebord des supports. Ne forcez pas la tablette en place car elle pourrait craquer. 7
. Fixez la tablette au foyer. À partir de l ouverture à chaque bout, fi xez le support interne de la tablette au support installé sur le foyer à l aide du boulon et de la rondelle. Ceci peut être fait à la main s il n y a pas assez d espace pour un tournevis. Ne serrez pas trop car la tablette pourrait craquer. Pièces 00USB Tablette supérieure noire Pièce n o Tablette supérieure 0065 Support gauche 00665 Support droit 00666 Couvercles du bout () 0066 Vis à métaux n o 8-/8 (8) Boulons M6 x 0 mm () Rondelles (). Placez un couvercle à chaque bout en l insérant tel qu indiqué. installez avec espace vers l extérieur 00LSB Tablette inférieure noire Pièce n o Tablette inférieure 006 Support gauche 0069 Support droit 0069 Couvercles du bout () 006 Vis à métaux n o 8-/8 (6) Boulons M6 x 0 mm () Rondelles () 5. Protégez la tablette durant l application de la fi nition du mur en utilisant du ruban à masquer ou un fi lm de plastique entre la fi nition et la tablette. Parce que nous favorisons une politique de développement continu, certains détails de la présente publication peuvent varier. Conçue et fabriquée par / pour Miles Industries Ltd. 90 55 Dollarton Highway, North Vancouver, BC, CANADA V7H B Tél. 60-98-96 Téléc. 60-98-06 www.foyervalor.com 8