11 KIT 7214 decal placement 85721400200 '80 ford bronco Whether at work or at play, combining good looks and performance, the Bronco has secured its place in automotive history as a milestone truck. The Bronco is a highly civilized, multipurpose vehicle that is capable of navigating some of the most demanding terrain. It evolved from a lightweight vehicle during the mid sixties into a comfortable off-road machine. Your Monogram model features an opening hood with detailed V-8 engine and four wheel drive chassis with all terrain tires and spoked alloy wheels, an optional rear roof cover, fender flairs, rear seat, roll bar with off road lights, a roof rack with skis and decals with stock and custom graphics. * REPEAT SEVERAL TIMES * REPEAT PROCEDURE ` ` LE PROCEDE ` ` * A REPETER PLUSIEURS FOIS * REPETEZ * OPTIONAL PARTS * PIECES EN OPTION READ THIS BEFE YOU BEGIN * Study the assembly drawings. * Each plastic part is identified by a number. * In the assembly drawings, some parts will be marked by a star ( ) to indicate chrome plated plastic. * For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry. * Check the fit of each piece before cementing in place. * Use only cement for polystyrene plastic. * Scrape plating and paint from areas to be cemented. * Allow paint to dry thoroughly before handling parts. * Any unused parts may be discarded. 6. 7. 8. 9. Cut desired decal from sheet. Dip decal in water for a few seconds. Place wet decal on paper towel. Wait until decal is movable on paper backing. Place decal in position on model, face up and slide backing away. Press out air bubbles with a soft damp cloth. Milkiness that may appear is for better decal adhesion and will dry clear. Wipe away any excess adhesive. Do not touch decal until fully dry. Allow the decals 48 hours to dry before applying clear coat. NOTE: Decals are compatible with setting solutions or solvents. * ASSEMBLY CAUTION * CEMENT TOGETHER * REMOVE AND THROW AWAY * DO NOT CEMENT * NE PAS COLLER * A RETIRER ET JETER * A COLLER *ATTENTION` D ASSEMBLEE LIRE CE QUI SUIT AVANT DE COMMENCER This paint guide is provided to complete this kit as shown on the box. * Etudier les schémas de montage. * Chaque pièce en plastique est identifiée par un numéro. * Sur les schémas de montage, certaines pièces sont marquées d'une étoile ( ) pour indiquer qu'elles sont en plastique chromé. * Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air. * Vérifier que chaque pièce s'ajuste bien avant de la coller en place. * N'utiliser que de la colle pour polystyrène. * Gratter les parties à coller pour enlever le chrome et la peinture. * Laisser la peinture bien sécher avant de manipuler les pièces. * Toute pièce inutilisée peut être jetée. Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte. DIRECTIVES D'APPLICATION DES AUTOCOLLANTS DECAL APPLICATION INSTRUCTIONS 1. 2. 3. 4. 5. * DECAL * DECAL COMANIE 1. 2. 3. 4. 5. 6. 7. 8. 9. Découper l'autocollant désiré de la feuille. Tremper l'autocollant dans de l'eau pendant quelques secondes. Placer l'autocollant mouillé sur une serviette en papier. Attendez que l'autocollant puisse être déplacé sur son support en papier. Mettre l'autocollant en position sur le modèle face sur le dessus et faire glisser le support pour l'enlever. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air. La substance laiteuse qui peut apparaître est destinée à améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec. Laisser l'autocollant sécher pendant 48 heures avant d'appliquer une couche transparente. REMARQUE: Les autocollants sont compatibles avec les solutions de fixage ou les solvants. Aluminum Aluminum Flat Tan Mat havane Gloss Bright Blue Bleu brillant Red Rouge Ford Engine Blue Bleu moteur Ford Semi Gloss Black Noir satiné Silver Argent Steel Acier Turn Signal Amber Ambre transparent Transparent Red Rouge transparent If you have any questions or comments, call our hotline at: (800) 833-3570 or, please write to: Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007 Be sure to include the plan number (85721400200), part number, description, your return address and phone number. Kit 7214 - Page 8 Visit our website: www.revell.com Revell Inc Elk Grove Village, IL. Copyright 2010. All rights reserved.
1 9 ENGINE ASSEMBLY 32 CARBURET 28 ENGINE HALF hood assembly 11 HOOD BODY COL 31 INTAKE MANIFOLD 27 ENGINE HALF 60 VALVE COVER 34 VALVE COVER 38 ALTERNAT 35 CYLINDER HEAD 10 41 FAN 35 CYLINDER HEAD mirror / rack assembly DECAL NOTE: IF USING DECALS #19,20,21,22 APPLY DECALS BEFE ATTACHING SIDE MIRRS 53 RACK CENTER SUPPTS 51 ROOF RACK END 39 WATER PUMP 51 ROOF RACK END 40 BELT ASSEMBLY 49 DISTRIBUT 30 EXHAUST HEADER 19 SIDE VIEW MIRR 20 SIDE VIEW MIRR 29 EXHAUST HEADER 14 SKI RACK 37 TRANSFER CASE 36 TRANSFER CASE 21 FRAME COMPLETED ENGINE ASSEMBLY TOP VIEW SKI RACK (SKI BOOTS) Kit 7214 - Page 2 Kit 7214 - Page 7
7 2 RADIAT ASSEMBLY 48 EXHAUST CROSS OVER PIPE 33 AIR CLEANER 46 FAN SHROUD 54 BRUSH GUARD wheel / AXLE ASSEMBLY 18 WHEEL RETAINER 200 TIRE 16 WHEEL 42 RADIAT 17 INNER WHEEL 8 rear / ROOF ASSEMBLY 23 REAR AXLE ASSEMBLY 76 TAILLIGHT TAILLIGHTS 52 CUSTOM OUTER WHEEL TRANSPARENT 74 TAILLIGHT 91 REAR BUMPER 92 REAR SHOCK ABSBER 59 GAS CAN 13 SPARE TIRE BRACKET 22 AXLE ASSEMBLY 92 REAR SHOCK ABSBER 12 SPARE TIRE COVER 8 ROOF 2 SPARE TIRE COVER 58 GAS CAN 25 SKID PLATE 80 REAR WINDOW 24 SPRING TRACKE A E GOOD Y Kit 7214 - Page 6 R R -T 79 REAR SIDE WINDOW A 78 REAR SIDE WINDOW 24 SPRING Kit 7214 - Page 3
3 5 window / flare ASSEMBLY 1 BODY BODY COL INTERI assembly 73 WINDSHIELD 9 SEAT FLAT TAN 43 REAR VIEW MIRR 50 REAR SEAT FLAT TAN 10 SEAT 44 REAR SEAT FLAT TAN AMBER 65 64 REAR FLAT TAN 18 LIGHT HOUSING 75 OFF-ROAD LIGHT LENS ROLL BAR CANNOT BE USED IF USED WITH ROOF SEE STEP 8 INTERI TO BODY 55 ROLL BAR AMBER 67 68 REAR 56 ROLL BAR SUPPTS 4 dashboard ASSEMBLY 6 5 FOUR WHEEL DRIVE SHIFTER 4 DASHBOARD 6 STEERING WHEEL BODY TO FRAME 45 GRILLE FLAT TAN ( DETAILS) assembly (RECESSED AREAS ) 71 HEAD LIGHT LENS 26 SHIFTER FLAT TAN 72 TURN SIGNAL LENS 7 STEERING COLUMN SHADED AREA Kit 7214 - Page 4 (AMBER) 3 INTERI FLAT TAN WITH FLO 15 BUMPER 57 WINCH Kit 7214 - Page 5
3 5 window / flare ASSEMBLY 1 BODY BODY COL INTERI assembly 73 WINDSHIELD 9 SEAT FLAT TAN 43 REAR VIEW MIRR 50 REAR SEAT FLAT TAN 10 SEAT 44 REAR SEAT FLAT TAN AMBER 65 64 REAR FLAT TAN 18 LIGHT HOUSING 75 OFF-ROAD LIGHT LENS ROLL BAR CANNOT BE USED IF USED WITH ROOF SEE STEP 8 INTERI TO BODY 55 ROLL BAR AMBER 67 68 REAR 56 ROLL BAR SUPPTS 4 dashboard ASSEMBLY 6 5 FOUR WHEEL DRIVE SHIFTER 4 DASHBOARD 6 STEERING WHEEL BODY TO FRAME 45 GRILLE FLAT TAN ( DETAILS) assembly (RECESSED AREAS ) 71 HEAD LIGHT LENS 26 SHIFTER FLAT TAN 72 TURN SIGNAL LENS 7 STEERING COLUMN SHADED AREA Kit 7214 - Page 4 (AMBER) 3 INTERI FLAT TAN WITH FLO 15 BUMPER 57 WINCH Kit 7214 - Page 5
7 2 RADIAT ASSEMBLY 48 EXHAUST CROSS OVER PIPE 33 AIR CLEANER 46 FAN SHROUD 54 BRUSH GUARD wheel / AXLE ASSEMBLY 18 WHEEL RETAINER 200 TIRE 16 WHEEL 42 RADIAT 17 INNER WHEEL 8 rear / ROOF ASSEMBLY 23 REAR AXLE ASSEMBLY 76 TAILLIGHT TAILLIGHTS 52 CUSTOM OUTER WHEEL TRANSPARENT 74 TAILLIGHT 91 REAR BUMPER 92 REAR SHOCK ABSBER 59 GAS CAN 13 SPARE TIRE BRACKET 22 AXLE ASSEMBLY 92 REAR SHOCK ABSBER 12 SPARE TIRE COVER 8 ROOF 2 SPARE TIRE COVER 58 GAS CAN 25 SKID PLATE 80 REAR WINDOW 24 SPRING TRACKE A E GOOD Y Kit 7214 - Page 6 R R -T 79 REAR SIDE WINDOW A 78 REAR SIDE WINDOW 24 SPRING Kit 7214 - Page 3
1 9 ENGINE ASSEMBLY 32 CARBURET 28 ENGINE HALF hood assembly 11 HOOD BODY COL 31 INTAKE MANIFOLD 27 ENGINE HALF 60 VALVE COVER 34 VALVE COVER 38 ALTERNAT 35 CYLINDER HEAD 10 41 FAN 35 CYLINDER HEAD mirror / rack assembly DECAL NOTE: IF USING DECALS #19,20,21,22 APPLY DECALS BEFE ATTACHING SIDE MIRRS 53 RACK CENTER SUPPTS 51 ROOF RACK END 39 WATER PUMP 51 ROOF RACK END 40 BELT ASSEMBLY 49 DISTRIBUT 30 EXHAUST HEADER 19 SIDE VIEW MIRR 20 SIDE VIEW MIRR 29 EXHAUST HEADER 14 SKI RACK 37 TRANSFER CASE 36 TRANSFER CASE 21 FRAME COMPLETED ENGINE ASSEMBLY TOP VIEW SKI RACK (SKI BOOTS) Kit 7214 - Page 2 Kit 7214 - Page 7
11 KIT 7214 decal placement 85721400200 '80 ford bronco Whether at work or at play, combining good looks and performance, the Bronco has secured its place in automotive history as a milestone truck. The Bronco is a highly civilized, multipurpose vehicle that is capable of navigating some of the most demanding terrain. It evolved from a lightweight vehicle during the mid sixties into a comfortable off-road machine. Your Monogram model features an opening hood with detailed V-8 engine and four wheel drive chassis with all terrain tires and spoked alloy wheels, an optional rear roof cover, fender flairs, rear seat, roll bar with off road lights, a roof rack with skis and decals with stock and custom graphics. * REPEAT SEVERAL TIMES * REPEAT PROCEDURE ` ` LE PROCEDE ` ` * A REPETER PLUSIEURS FOIS * REPETEZ * OPTIONAL PARTS * PIECES EN OPTION READ THIS BEFE YOU BEGIN * Study the assembly drawings. * Each plastic part is identified by a number. * In the assembly drawings, some parts will be marked by a star ( ) to indicate chrome plated plastic. * For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry. * Check the fit of each piece before cementing in place. * Use only cement for polystyrene plastic. * Scrape plating and paint from areas to be cemented. * Allow paint to dry thoroughly before handling parts. * Any unused parts may be discarded. 6. 7. 8. 9. Cut desired decal from sheet. Dip decal in water for a few seconds. Place wet decal on paper towel. Wait until decal is movable on paper backing. Place decal in position on model, face up and slide backing away. Press out air bubbles with a soft damp cloth. Milkiness that may appear is for better decal adhesion and will dry clear. Wipe away any excess adhesive. Do not touch decal until fully dry. Allow the decals 48 hours to dry before applying clear coat. NOTE: Decals are compatible with setting solutions or solvents. * ASSEMBLY CAUTION * CEMENT TOGETHER * REMOVE AND THROW AWAY * DO NOT CEMENT * NE PAS COLLER * A RETIRER ET JETER * A COLLER *ATTENTION` D ASSEMBLEE LIRE CE QUI SUIT AVANT DE COMMENCER This paint guide is provided to complete this kit as shown on the box. * Etudier les schémas de montage. * Chaque pièce en plastique est identifiée par un numéro. * Sur les schémas de montage, certaines pièces sont marquées d'une étoile ( ) pour indiquer qu'elles sont en plastique chromé. * Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air. * Vérifier que chaque pièce s'ajuste bien avant de la coller en place. * N'utiliser que de la colle pour polystyrène. * Gratter les parties à coller pour enlever le chrome et la peinture. * Laisser la peinture bien sécher avant de manipuler les pièces. * Toute pièce inutilisée peut être jetée. Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte. DIRECTIVES D'APPLICATION DES AUTOCOLLANTS DECAL APPLICATION INSTRUCTIONS 1. 2. 3. 4. 5. * DECAL * DECAL COMANIE 1. 2. 3. 4. 5. 6. 7. 8. 9. Découper l'autocollant désiré de la feuille. Tremper l'autocollant dans de l'eau pendant quelques secondes. Placer l'autocollant mouillé sur une serviette en papier. Attendez que l'autocollant puisse être déplacé sur son support en papier. Mettre l'autocollant en position sur le modèle face sur le dessus et faire glisser le support pour l'enlever. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air. La substance laiteuse qui peut apparaître est destinée à améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec. Laisser l'autocollant sécher pendant 48 heures avant d'appliquer une couche transparente. REMARQUE: Les autocollants sont compatibles avec les solutions de fixage ou les solvants. Aluminum Aluminum Flat Tan Mat havane Gloss Bright Blue Bleu brillant Red Rouge Ford Engine Blue Bleu moteur Ford Semi Gloss Black Noir satiné Silver Argent Steel Acier Turn Signal Amber Ambre transparent Transparent Red Rouge transparent If you have any questions or comments, call our hotline at: (800) 833-3570 or, please write to: Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007 Be sure to include the plan number (85721400200), part number, description, your return address and phone number. Kit 7214 - Page 8 Visit our website: www.revell.com Revell Inc Elk Grove Village, IL. Copyright 2010. All rights reserved.