9 KIT 4286 decal placement '69 Dodge Charger 85428600200 NHRA funny car The Chi-Town Hustler was one of the top winning and most popular funny cars of the late 60's and early 70's. This famous 1969 Dodge Charger funny car belonged to the team of Farkonas, Coil, and Minick. With Pat Minnik as driver the awesome mini Charger did spectacular 1/8 quarter mile burn outs and has posted a top quarter mile time of 6.7 seconds at 220 mph. Your Revell model features a highly detailed supercharged 426 cubic inch Chrysler HEMI engine, an accurate Mini Dodge Charger body that lifts to show the custom made offset Farkonas designed chassis and authentic vintage Chi-Town Hustler drag graphics. * REPEAT SEVERAL TIMES * REPEAT PROCEDURE * OPTIONAL PARTS * DECAL * ASSEMBLY CAUTION * CEMENT TOGETHER * REMOVE AND THROW AWAY * DO NOT CEMENT ` ` LE PROCEDE ` ` * PIECES EN OPTION * DECAL COMANIE *ATTENTION`D ASSEMBLEE * A REPETER PLUSIEURS FOIS * REPETEZ * NE PAS COLLER * A RETIRER ET JETER * A COLLER LIRE CE QUI SUIT AVANT DE COMMENCER This paint guide is provided to complete this kit as shown on the box. * Etudier les schémas de montage. * Chaque pièce en plastique est identifiée par un numéro. * Sur les schémas de montage, certaines pièces sont marquées d'une étoile ( ) pour indiquer qu'elles sont en plastique chromé. * Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air. * Vérifier que chaque pièce s'ajuste bien avant de la coller en place. * N'utiliser que de la colle pour polystyrène. * Gratter les parties à coller pour enlever le chrome et la peinture. * Laisser la peinture bien sécher avant de manipuler les pièces. * Toute pièce inutilisée peut être jetée. Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte. READ THIS BEFORE YOU BEGIN * Study the assembly drawings. * Each plastic part is identified by a number. * In the assembly drawings, some parts will be marked by a star ( ) to indicate chrome plated plastic. * For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry. * Check the fit of each piece before cementing in place. * Use only cement for polystyrene plastic. * Scrape plating and paint from areas to be cemented. * Allow paint to dry thoroughly before handling parts. * Any unused parts may be discarded. DIRECTIVES D'APPLICATION DES AUTOCOLLANTS DECAL APPLICATION INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. Cut desired decal from sheet. Dip decal in water for a few seconds. Place wet decal on paper towel. Wait until decal is movable on paper backing. Place decal in position on model, face up and slide backing away. Press out air bubbles with a soft damp cloth. Milkiness that may appear is for better decal adhesion and will dry clear. Wipe away any excess adhesive. Do not touch decal until fully dry. Allow the decals 48 hours to dry before applying clear coat. NOTE: Decals are compatible with setting solutions or solvents. 1. 2. 3. 4. 5. 6. 7. 8. 9. Découper l'autocollant désiré de la feuille. Tremper l'autocollant dans de l'eau pendant quelques secondes. Placer l'autocollant mouillé sur une serviette en papier. Attendez que l'autocollant puisse être déplacé sur son support en papier. Mettre l'autocollant en position sur le modèle face sur le dessus et faire glisser le support pour l'enlever. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air. La substance laiteuse qui peut apparaître est destinée à améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec. Laisser l'autocollant sécher pendant 48 heures avant d'appliquer une couche transparente. Semi Gloss Black Noir satiné Gloss Red Rouge brillant Gloss Red Metallic Rouge brillant métallisé Aluminum Aluminium Silver Argent Transparent Blue Bleu transparent Transparent Red Rouge transparent REMARQUE: Les autocollants sont compatibles avec les solutions de fixage ou les solvants. If you have any questions or comments, call our hotline at: (800) 833-3570 or, please write to: Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007 Be sure to include the plan number (85428600200), part number, description, your return address and phone number. Kit 4286 - Page 8 Visit our website: www.revell.com Revell Inc Elk Grove Village, IL. Copyright 2010. All rights reserved.
1 ENGINE ASSEMBLY 51 ENGINE HALF H67 ROCKER COVER 54 INTAKE MANIFOLD H66 ROCKER COVER 50 ENGINE HALF 53 CYLINDER HEAD 53 CYLINDER HEAD 68 INJECTORS H64 SUPER CHARGER 55 OIL PAN H56 TRANSMISSION PAN H63 SUPER CHARGER 65 ENGINE BELT ( PULLEYS) 52 ENGINE H62 SUPER CHARGER BODY 60 OIL PUMP 69 BELT TENSIONER 75 OIL FILTER 70 OIL LINE 61 STARTER 3 FRAME 90 58 EXHAUST HEADER 57 EXHAUST HEADER VIEW SHOWING ANGLE OF EXHAUST be sure pipes are 90 from bottom of frame to top center of engine for proper fit when body is lowered down Kit 4286 - Page 2
5 2 wheel ASSEMBLY H37 INNER WHEEL SECOND H38 OUTER WHEEL H32 COVER DRAG SLICK H79 INNER WHEEL H36 OUTER WHEEL rear suspension ASSEMBLY RED 35 DISC BRAKE H77 WHEELIE BAR RED FIRST SEMI 31 BACK 30 FRIONT TIRE 34 DISC BRAKE H76 WHEELIE BARS METAL AXLE H42 AXLE CAP 95 SHOCK H42 AXLE CAP 6 ROTATE TIRES ON A PIECE OF SAND PAPER TO REMOVE SEAM AND GIVE A MORE REALISTIC APPERANCE WINDOWS ASSEMBLY 92 SIDE WINDOW 95 SHOCK 59 DRIVESHAFT 29 27 90 WINDSHIELD 91 WINDOW 2 HOOD 28 METALLIC ( INSIDE) 47 SPOILER METALLIC 93 SIDE WINDOW Kit 4286 - Page 6 Kit 4286 - Page 3
3 front suspension ASSEMBLY 10 FRAME H8 H4 AXLE H6 TIE ROD H9 H14 OIL TANK TOP H39 FUEL TANK TOP H40 FUEL TANK BOTTOM H12 OIL TANK H13 OIL TANK H73 FUEL TANK SUPPORT H5 SHOCKS H7 STEERING LINKAGE Kit 4286 - Page 4
4 cockpit / steering assembly 97 ROLL CAGE SIDE 21 ROLL CAGE H25 SHIFT LEVER 20 ROLL CAGE 96 ROLL CAGE SIDE 18 COCKPIT WALL 17 COCKPIT BUCKET BUCKET (BELT BUCKLES SILVER) (SEAT ) H26 STEERING WHEEL (RIM) H23 STEERING COLUMN 22 STEERING COLUMN SUPPORT CUT-A-WAY SHOWING hole for column Kit 4286 - Page 5
5 2 wheel ASSEMBLY H37 INNER WHEEL SECOND H38 OUTER WHEEL H32 COVER DRAG SLICK H79 INNER WHEEL H36 OUTER WHEEL rear suspension ASSEMBLY RED 35 DISC BRAKE H77 WHEELIE BAR RED FIRST SEMI 31 BACK 30 FRIONT TIRE 34 DISC BRAKE H76 WHEELIE BARS METAL AXLE H42 AXLE CAP 95 SHOCK H42 AXLE CAP 6 ROTATE TIRES ON A PIECE OF SAND PAPER TO REMOVE SEAM AND GIVE A MORE REALISTIC APPERANCE WINDOWS ASSEMBLY 92 SIDE WINDOW 95 SHOCK 59 DRIVESHAFT 29 27 90 WINDSHIELD 91 WINDOW 2 HOOD 28 METALLIC ( INSIDE) 47 SPOILER METALLIC 93 SIDE WINDOW Kit 4286 - Page 6 Kit 4286 - Page 3
7 1 BODY METALLIC (INSIDE) BODY assembly 80 PIVOT BRACKETS 16 COCKPIT SHROUD bulkhead goes in front of the front rib 81 BULKHEAD RIB 78 COCKPIT PANEL 8 rear / final assembly CUT-A-WAY SHOWING THE PIVOT BRACKETS H24 SPOILER H71 SPOILER 13 DECAL 34 DECAL 44 CHUTE SILVER BUMPER 33 DISPLAY SUPPORT SILVER BUMPER H43 CHUTE PLATE 44 CHUTE Kit 4286 - Page 7
9 KIT 4286 decal placement '69 Dodge Charger 85428600200 NHRA funny car The Chi-Town Hustler was one of the top winning and most popular funny cars of the late 60's and early 70's. This famous 1969 Dodge Charger funny car belonged to the team of Farkonas, Coil, and Minick. With Pat Minnik as driver the awesome mini Charger did spectacular 1/8 quarter mile burn outs and has posted a top quarter mile time of 6.7 seconds at 220 mph. Your Revell model features a highly detailed supercharged 426 cubic inch Chrysler HEMI engine, an accurate Mini Dodge Charger body that lifts to show the custom made offset Farkonas designed chassis and authentic vintage Chi-Town Hustler drag graphics. * REPEAT SEVERAL TIMES * REPEAT PROCEDURE * OPTIONAL PARTS * DECAL * ASSEMBLY CAUTION * CEMENT TOGETHER * REMOVE AND THROW AWAY * DO NOT CEMENT ` ` LE PROCEDE ` ` * PIECES EN OPTION * DECAL COMANIE *ATTENTION`D ASSEMBLEE * A REPETER PLUSIEURS FOIS * REPETEZ * NE PAS COLLER * A RETIRER ET JETER * A COLLER LIRE CE QUI SUIT AVANT DE COMMENCER This paint guide is provided to complete this kit as shown on the box. * Etudier les schémas de montage. * Chaque pièce en plastique est identifiée par un numéro. * Sur les schémas de montage, certaines pièces sont marquées d'une étoile ( ) pour indiquer qu'elles sont en plastique chromé. * Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air. * Vérifier que chaque pièce s'ajuste bien avant de la coller en place. * N'utiliser que de la colle pour polystyrène. * Gratter les parties à coller pour enlever le chrome et la peinture. * Laisser la peinture bien sécher avant de manipuler les pièces. * Toute pièce inutilisée peut être jetée. Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte. READ THIS BEFORE YOU BEGIN * Study the assembly drawings. * Each plastic part is identified by a number. * In the assembly drawings, some parts will be marked by a star ( ) to indicate chrome plated plastic. * For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry. * Check the fit of each piece before cementing in place. * Use only cement for polystyrene plastic. * Scrape plating and paint from areas to be cemented. * Allow paint to dry thoroughly before handling parts. * Any unused parts may be discarded. DIRECTIVES D'APPLICATION DES AUTOCOLLANTS DECAL APPLICATION INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. Cut desired decal from sheet. Dip decal in water for a few seconds. Place wet decal on paper towel. Wait until decal is movable on paper backing. Place decal in position on model, face up and slide backing away. Press out air bubbles with a soft damp cloth. Milkiness that may appear is for better decal adhesion and will dry clear. Wipe away any excess adhesive. Do not touch decal until fully dry. Allow the decals 48 hours to dry before applying clear coat. NOTE: Decals are compatible with setting solutions or solvents. 1. 2. 3. 4. 5. 6. 7. 8. 9. Découper l'autocollant désiré de la feuille. Tremper l'autocollant dans de l'eau pendant quelques secondes. Placer l'autocollant mouillé sur une serviette en papier. Attendez que l'autocollant puisse être déplacé sur son support en papier. Mettre l'autocollant en position sur le modèle face sur le dessus et faire glisser le support pour l'enlever. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air. La substance laiteuse qui peut apparaître est destinée à améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec. Laisser l'autocollant sécher pendant 48 heures avant d'appliquer une couche transparente. Semi Gloss Black Noir satiné Gloss Red Rouge brillant Gloss Red Metallic Rouge brillant métallisé Aluminum Aluminium Silver Argent Transparent Blue Bleu transparent Transparent Red Rouge transparent REMARQUE: Les autocollants sont compatibles avec les solutions de fixage ou les solvants. If you have any questions or comments, call our hotline at: (800) 833-3570 or, please write to: Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007 Be sure to include the plan number (85428600200), part number, description, your return address and phone number. Kit 4286 - Page 8 Visit our website: www.revell.com Revell Inc Elk Grove Village, IL. Copyright 2010. All rights reserved.